- 您現在的位置：買賣IC網 > PDF目錄1895 > AD9983AKSTZ-170 (Analog Devices Inc)IC DISPLAY 8BIT 170MSPS 80LQFP PDF資料下載
參數資料
| 型號： | AD9983AKSTZ-170 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DISPLAY 8BIT 170MSPS 80LQFP |
| 標準包裝： | 1 |
| 應用： | 視頻 |
| 接口： | 模擬 |
| 電源電壓： | 1.7 V ~ 3.47 V |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（14x14） |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9983A
Rev. 0 | Page 18 of 44
POWER MANAGEMENT
To meet display requirements for low standby power, the
AD9983A includes a power-down mode. The power-down state
can be controlled manually (via Pin 17 or Register 0x1E, Bit 3),
or automatically by the chip. If automatic control is selected
(Register 0x1E, Bit 4), the AD9983A decision is based on the
status of the sync detect bits (Register 0x24, Bit 2, Bit 3, Bit 6,
and Bit 7). If either an Hsync or a sync-on-green input is
detected on any input, the chip powers up, otherwise it powers
down. For manual control, the AD9983A allows flexibility of
control through both a dedicated pin and a register bit. The
dedicated pin allows a hardware watchdog circuit to control
power-down, while the register bit allows power-down to be
controlled by software. With manual power-down control, the
polarity of the power-down pin must be set (Register 0x1E, Bit 2)
whether the pin is used or not. If unused, it is recommended to
set the polarity to active high and hardwire the pin to ground with
a 10 kΩ resistor.
In power-down mode, there are several circuits that continue to
operate as normal. The serial register and sync detect circuits
maintain power so that the AD9983A can be woken up from
its power-down state. The bandgap circuit maintains power
because it is needed for sync detection. The sync-on-green and
SOGOUT functions continue to operate because the SOGOUT
output is needed when sync detection is performed by a
secondary chip. All of these circuits require minimal power to
operate. Typical standby power on the AD9983A is about 50 mW.
There are two options that can be selected when in power-
down. These are controlled by Bit 0 and Bit 1 in Register 0x1E.
Bit 0 controls whether the SOGOUT pin is in high impedance
or not. In most cases, the user will not place SOGOUT in high
impedance during normal operation. The option to put
SOGOUT in high impedance is included mainly to allow for
factory testing modes. Bit 1 keeps the AD9983A powered up
while placing only the outputs in high impedance. This option
is useful when the data outputs from two chips are connected
on a PCB and the user wants to switch instantaneously between
the two.
Table 11. Power-Down Control and Mode Descriptions
Inputs
Mode
Auto Power-Down
Control1
Power-Down2
Sync Detect3
Powered On/Comments
Power-Up
1
X
1
Everything
Power-Down
1
X
0
Only the serial bus, sync activity detect,
SOG, bandgap reference
Power-Up
0
X
Everything
Power-Down
0
1
X
Only the serial bus, sync activity detect,
SOG, bandgap reference
1 Auto power-down control is set by Register 0x1E, Bit 4.
2 Power-down is controlled by OR’ing Pin 17 with Register 0x1E, Bit 3. The polarity of Pin 17 is set by Register 0x1E, Bit 2.
3 Sync detect is determined by OR’ing Register 0x24, Bit 2, Bit 3, Bit 6, and Bit 7.
TIMING DIAGRAMS
The timing diagrams in Figure 13 to Figure 16 show the operation of the AD9983A. The output data clock signal is created so that its
rising edge always occurs between data transitions and can be used to latch the output data externally. There is a pipeline in the
AD9983A, which must be flushed before valid data becomes available. This means six data sets are presented before valid data is available.
tPER
tDCYCLE
tSKEW
DATACK
DATA
HSOUT
06
47
5-
00
7
Figure 13. Output Timing
相關PDF資料 |
PDF描述 |
|---|---|
| AD9985KSTZ-140 | IC INTERFACE 8BIT 140MSPS 80LQFP |
| AD9990BBCZ | IC CCD SGNL PROCESSOR 112CSPBGA |
| AD9991KCPZRL | IC CCD SIGNAL PROCESSOR 56-LFCSP |
| AD9992BBCZRL | IC CCD SGNL PROC 12BIT 105CSPBGA |
| AD9995KCPZ | IC CCD SIGNAL PROCESSOR 56-LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9983AKSTZ-1701 | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9983KSTZ-110 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9983KSTZ-140 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9983KSTZ-170 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Analog Devices 功能描述: |
| AD9984A | 制造商:AD 制造商全稱:Analog Devices 功能描述:High Performance 10-Bit Display Interface |
發布緊急采購，3分鐘左右您將得到回復。