- 您現在的位置：買賣IC網 > PDF目錄10527 > AD9634BCPZ-170 (Analog Devices Inc)IC ADC 12BIT 170MSPS 32-LFCSP PDF資料下載
參數資料
| 型號： | AD9634BCPZ-170 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 170MSPS 32-LFCSP |
| 標準包裝： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 170M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 340mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 32-LFCSP-WQ（5x5） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 單端，1 個差分 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD9634
Rev. 0 | Page 24 of 32
SERIAL PORT INTERFACE (SPI)
The AD9634 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI offers
added flexibility and customization, depending on the application.
Addresses are accessed via the serial port and can be written to
or read from via the port. Memory is organized into bytes that can
be further divided into fields. These fields are documented in the
Memory Map section. For detailed operational information, see
the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: the SCLK pin, the SDIO
pin, and the CSB pin (see Table 11). The SCLK (serial clock) pin
is used to synchronize the read and write data presented from
and to the ADC. The SDIO (serial data input/output) pin is a
dual-purpose pin that allows data to be sent and read from the
internal ADC memory map registers. The CSB (chip select bar)
pin is an active-low control that enables or disables the read and
write cycles.
Table 11. Serial Port Interface Pins
Pin
Function
SCLK
Serial clock. The serial shift clock input, which is used to
synchronize serial interface reads and writes.
SDIO
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending on
the instruction being sent and the relative position in the
timing frame.
CSB
Chip select bar. An active-low control that gates the read
and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the serial
Other modes involving the CSB are available. The CSB can be
held low indefinitely, which permanently enables the device;
this is called streaming. The CSB can stall high between bytes to
allow for additional external timing. When CSB is tied high, SPI
functions are placed in a high impedance mode. This mode turns
on any SPI pin secondary functions.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits.
All data is composed of 8-bit words. The first bit of each individual
byte of serial data indicates whether a read or write command is
issued. This allows the serial data input/output (SDIO) pin to
change direction from an input to an output.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an output
at the appropriate point in the serial frame.
Data can be sent in MSB-first mode or in LSB-first mode. MSB-
first mode is the default on power-up and can be changed via
the SPI port configuration register. For more information about
this and other features, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
HARDWARE INTERFACE
The pins described in Table 11 comprise the physical interface
between the user programming device and the serial port of the
AD9634. The SCLK pin and the CSB pin function as inputs when
using the SPI interface. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during readback.
The SPI interface is flexible enough to be controlled by either
FPGAs or microcontrollers. One method for SPI configuration
is described in detail in the AN-812 Application Note,
Microcontroller-Based Serial Port Interface (SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9634 to prevent these signals from transi-
tioning at the converter inputs during critical sampling periods.
相關PDF資料 |
PDF描述 |
|---|---|
| DS34LV87TM/NOPB | IC LINE DRIVER QUAD CMOS 16-SOIC |
| AD7711ANZ | IC ADC 24BIT RTD I SOURCE 24-DIP |
| AD9600ABCPZ-125 | IC ADC 10BIT 125MSPS 64LFCSP |
| ICL3237CAZ | IC 5DRVR/3RCVR RS232 3V 28-SSOP |
| AMIS42665TJAA1G | TRANSCEIVER CAN HS LP 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9634BCPZ-210 | 制造商:Analog Devices 功能描述:12 BIT 210 MSPS ADC - Trays 制造商:Analog Devices 功能描述:IC ADC 12BIT 210MSPS 32-LFCSP 制造商:Analog Devices 功能描述:ADC 12BIT 210MSPS 32LFCSP 制造商:Analog Devices 功能描述:IC ADC 12 bit 210 MSPS Ser 制造商:Analog Devices 功能描述:ADC, 12BIT, 210MSPS, 32LFCSP 制造商:Analog Devices 功能描述:12 Bit 210 Msps ADC 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD9634BCPZ-250 | 制造商:Analog Devices 功能描述:12 BIT 250 MSPS ADC - Trays 制造商:Analog Devices 功能描述:IC ADC 12BIT 250MSPS 32-LFCSP 制造商:Analog Devices 功能描述:IC ADC 12 bit 250 MSPS Ser 制造商:Analog Devices 功能描述:ADC 12BIT 250MSPS 32LFCSP 制造商:Analog Devices 功能描述:ADC, 12BIT, 250MSPS, 32LFCSP 制造商:Analog Devices 功能描述:12 Bit 250 Msps ADC 制造商:Analog Devices 功能描述:CONVERTER - ADC |
| AD9634BCPZRL7-170 | 功能描述:IC ADC 12BIT SRL 170MSPS 32LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9634BCPZRL7-210 | 功能描述:模數轉換器 - ADC 12 Bit 210 Msps ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9634BCPZRL7-250 | 功能描述:模數轉換器 - ADC 12 Bit 250 Msps ADC RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。