- 您現在的位置：買賣IC網 > PDF目錄1987 > AD9558BCPZ-REEL7 (Analog Devices Inc)IC CLK XLATR PLL 1250MHZ 64LFCSP PDF資料下載
參數資料
| 型號： | AD9558BCPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 49/104頁 |
| 文件大小： | 0K |
| 描述： | IC CLK XLATR PLL 1250MHZ 64LFCSP |
| 產品變化通告： | AD9558 Minor Metal Mask Change 17/Apr/2012 |
| 標準包裝： | 750 |
| 類型： | 時鐘/頻率轉換器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，Stratum |
| 輸入： | CMOS，LVDS，LVPECL |
| 輸出： | CMOS，HSTL，LVDS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 4:6 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.25GHz |
| 電源電壓： | 1.71 V ~ 3.465 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁
Data Sheet
AD9558
Rev. B | Page 49 of 104
SERIAL CONTROL PORT
The AD9558 serial control port is a flexible, synchronous serial
communications port that provides a convenient interface to
many industry-standard microcontrollers and microprocessors.
The AD9558 serial control port is compatible with most
synchronous transfer formats, including IC, Motorola SPI, and
Intel SSR protocols. The serial control port allows read/write
access to the AD9558 register map.
In SPI mode, single or multiple byte transfers are supported.
The SPI port configuration is programmable via Register 0x0000.
This register is integrated into the SPI control logic rather than
in the register map and is distinct from the I2C Register 0x0000.
It is also inaccessible to the EEPROM controller.
protocols, only one or the other is active following power-up (as
determined by the M0 and M1 multifunction pins during the
startup sequence). That is, the only way to change the serial port
protocol is to reset the device (or cycle the device power supply).
SPI/IC PORT SELECTION
Because the AD9558 supports both SPI and IC protocols, the
active serial port protocol depends on the logic state of the
PINCONTROL, M1, and M0 pins. The PINCONTROL pin
must be low, and the state of the M0 and M1 pins determines
I2C address assignments.
Table 24. SPI/IC Serial Port Setup
M1
M0
SPI/IC
Low
SPI
Low
Open
IC, 1101000
Low
High
IC, 1101001
Open
Low
IC, 1101010
Open
IC, 1101011
Open
High
IC, 1101100
High
Low
IC, 1101101
High
Open
IC, 1101110
High
IC, 1101111
SPI SERIAL PORT OPERATION
Pin Descriptions
The SCLK (serial clock) pin serves as the serial shift clock. This
pin is an input. SCLK synchronizes serial control port read and
write operations. The rising edge SCLK registers write data bits,
and the falling edge registers read data bits. The SCLK pin
supports a maximum clock rate of 40 MHz.
The SDIO (serial data input/output) pin is a dual-purpose pin
and acts as either an input only (unidirectional mode) or as
both an input and an output (bidirectional mode). The AD9558
default SPI mode is bidirectional.
The SDO (serial data output) pin is useful only in unidirectional
I/O mode. It serves as the data output pin for read operations.
The
EE
AA
(chip select) pin is an active low control that gates read
and write operations. This pin is internally connected to a 30 k
pull-up resistor. When
AA
CSEE
AA
is high, the SDO and SDIO pins go
into a high impedance state.
CS
SPI Mode Operation
The SPI port supports both 3-wire (bidirectional) and 4-wire
(unidirectional) hardware configurations and both MSB-first
and LSB-first data formats. Both the hardware configuration
and data format features are programmable. By default, the
AD9558 uses the bidirectional MSB-first mode. The reason that
bidirectional is the default mode is so that the user can still
write to the device, if it is wired for unidirectional operation, to
switch to unidirectional mode.
Assertion (active low) of the
AA
CSEE
AA
pin initiates a write or read
operation to the AD9558 SPI port. For data transfers of three
bytes or fewer (excluding the instruction word), the device
supports the
AA
CSEE
AA
stalled high mode (see Table 25). In this mode,
the
AA
CSEE
AA
pin can be temporarily deasserted on any byte boundary,
allowing time for the system controller to process the next byte.
AA
CSEE
AA
can be deasserted only on byte boundaries, however. This
applies to both the instruction and data portions of the transfer.
During stall high periods, the serial control port state machine
enters a wait state until all data is sent. If the system controller
decides to abort a transfer midstream, then the state machine must
be reset either by completing the transfer or by asserting the
AA
CSEE
AA
pin for at least one complete SCLK cycle (but less than eight
SCLK cycles). Deasserting the
AA
CSEE
AA
pin on a nonbyte boundary
terminates the serial transfer and flushes the buffer.
In streaming mode (see Table 25), any number of data bytes can
be transferred in a continuous stream. The register address is
automatically incremented or decremented.
AA
CSEE
AA
must be deasserted
at the end of the last byte that is transferred, thereby ending the
streaming mode.
Table 25. Byte Transfer Count
W1
W0
Bytes to Transfer
0
1
0
1
2
1
0
3
1
Streaming mode
Communication Cycle—Instruction Plus Data
The SPI protocol consists of a two-part communication cycle.
The first part is a 16-bit instruction word that is coincident with
the first 16 SCLK rising edges and a payload. The instruction
word provides the AD9558 serial control port with information
regarding the payload. The instruction word includes the R/
AA
WEE
AA
bit that indicates the direction of the payload transfer (that is, a
read or write operation). The instruction word also indicates
the number of bytes in the payload and the starting register
address of the first payload byte.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9571ACPZPEC-R7 | IC PLL CLOCK GEN 25MHZ 40LFCSP |
| AD9572ACPZLVD-R7 | IC PLL CLOCK GEN 25MHZ 40LFCSP |
| AD9573ARUZ-RL7 | IC PCI CLCOK GEN 25MHZ 16TSSOP |
| AD9575ARUZPEC | IC PLL CLOCK GEN 25MHZ 16TSSOP |
| AD9577BCPZ-R7 | IC CLOCK GENERATOR 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9559 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator |
| AD9559/PCBZ | 功能描述:時鐘和定時器開發工具 Multi-protocol line card dual clock RoHS:否 制造商:Texas Instruments 產品:Evaluation Modules 類型:Clock Conditioners 工具用于評估:LMK04100B 頻率:122.8 MHz 工作電源電壓:3.3 V |
| AD9559BCPZ | 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| AD9559BCPZ-REEL7 | 功能描述:時鐘發生器及支持產品 Multi-protocol line card dual clock RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| AD9559PCBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual PLL, Quad Input, Multiservice Line Card Adaptive Clock Translator |
發布緊急采購，3分鐘左右您將得到回復。