- 您現在的位置：買賣IC網 > PDF目錄9159 > AD9518-4ABCPZ (Analog Devices Inc)IC CLOCK GEN 6CH 1.8GHZ 48LFCSP PDF資料下載
參數資料
| 型號： | AD9518-4ABCPZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 32/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK GEN 6CH 1.8GHZ 48LFCSP |
| 標準包裝： | 1 |
| 類型： | 時鐘發生器，扇出配送 |
| PLL： | 是 |
| 輸入： | CMOS，LVDS，LVPECL |
| 輸出： | LVPECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:6 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.8GHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
AD9518-4
Data Sheet
Rev. B | Page 38 of 64
A sync operation brings all outputs that have not been excluded
(by the nosync bit) to a preset condition before allowing the
outputs to begin clocking in synchronicity. The preset condition
takes into account the settings in each of the channel’s start high
bit and its phase offset. These settings govern both the static
state of each output when the sync operation is happening and
the state and relative phase of the outputs when they begin
clocking again upon completion of the sync operation. Between
outputs and after synchronization, this allows for the setting of
phase offsets.
The AD9518 outputs are in pairs, sharing a channel divider
per pair. The synchronization conditions apply to both outputs
of a pair.
Each channel (a divider and its outputs) can be excluded from
any sync operation by setting the nosync bit of the channel.
Channels that are set to ignore SYNC (excluded channels) do not
set their outputs static during a sync operation, and their outputs
are not synchronized with those of the nonexcluded channels.
LVPECL Outputs—OUT0 to OUT3
The LVPECL differential voltage (VOD) is selectable from ~400 mV
to ~960 mV (see Register 0x0F0[3:2] to Register 0x0F5[3:2]).
The LVPECL outputs have dedicated pins for power supply
(VS_LVPECL), allowing a separate power supply to be used.
VS_LVPECL can be from 2.5 V to 3.3 V.
The LVPECL output polarity can be set as noninverting or
inverting, which allows for the adjustment of the relative
polarity of outputs within an application without requiring
a board layout change. Each LVPECL output can be powered
down or powered up, as needed. Because of the architecture of
the LVPECL output stages, there is the possibility of electrical
overstress and breakdown under certain power-down conditions.
For this reason, the LVPECL outputs have several power-down
modes. This includes a safe power-down mode that continues
to protect the output devices while powered down, although it
consumes somewhat more power than a total power-down. If
the LVPECL output pins are terminated, it is best to select the
safe power-down mode. If the pins are left floating (that is, not
connected), total power-down mode is fine.
GND
3.3V
OUT
06
43
3-
0
33
Figure 43. LVPECL Output Simplified Equivalent Circuit
RESET MODES
The AD9518 has several ways to force the chip into a reset
condition that restores all registers to their default values and
makes these settings active.
Power-On Reset—Start-Up Conditions When VS Is Applied
A power-on reset (POR) is issued when the VS power supply is
turned on. This initializes the chip to the power-on conditions
that are determined by the default register settings. These are
indicated in the Default Value (Hex) column of Table 42. At
power-on, the AD9518 also executes a sync operation, which
brings the outputs into phase alignment according to the default
settings.
Asynchronous Reset via the RESET Pin
An asynchronous hard reset is executed by momentarily pulling
RESET low. A reset restores the chip registers to the default settings.
Soft Reset via Register 0x000[2]
A soft reset is executed by writing Register 0x000[2] and
Register 0x000[5] = 1b. This bit is not self-clearing; it must be
cleared by writing Register 0x000[2] and Register 0x000[5] = 0b to
reset it and complete the soft reset operation. A soft reset restores
the default values to the internal registers. The soft reset bit does
not require an update registers command (Register 0x232) to be
issued.
POWER-DOWN MODES
Chip Power-Down via PD
The AD9518 can be put into a power-down condition by
pulling the PD pin low. Power-down turns off most of the
functions and currents inside the
. The chip remains in
this power-down state until
PD is brought back to logic high.
When the
wakes up, it returns to the settings
programmed into its registers prior to the power-down, unless
the registers are changed by new programming while the
PD
pin is held low.
The PD power-down shuts down the currents on the chip, except
the bias current that is necessary to maintain the LVPECL outputs
in a safe shutdown mode. This is needed to protect the LVPECL
output circuitry from damage that could be caused by certain
termination and load configurations when tristated. Because
this is not a complete power-down, it can be called sleep mode.
When the AD9518 is in a PD power-down, the chip is in the
following state:
The PLL is off (asynchronous power-down).
The VCO is off.
The CLK input buffer is off.
All dividers are off.
All LVPECL outputs are in safe off mode.
The serial control port is active, and the chip responds to
commands.
相關PDF資料 |
PDF描述 |
|---|---|
| SM843256KA | IC SYNTHESIZER LVPECL 24TSSOP |
| V110A36H300BG3 | CONVERTER MOD DC/DC 36V 300W |
| VI-B4W-MV | CONVERTER MOD DC/DC 5.5V 150W |
| V110A36H300BG2 | CONVERTER MOD DC/DC 36V 300W |
| VE-B2Z-MW-F2 | CONVERTER MOD DC/DC 2V 40W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9518-4ABCPZ-RL7 | 功能描述:IC CLOCK GEN 6CH 1.8GHZ 48LFCSP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| AD9518-4A-PCBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Output Clock Generator with Integrated 1.6 GHz VCO |
| AD9518-4BCPZ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| AD9518-4BCPZ-REEL7 | 制造商:Analog Devices 功能描述: |
| AD9520 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers |
發布緊急采購，3分鐘左右您將得到回復。