參數資料
型號： AD9517-4ABCPZ-RL7
廠商： Analog Devices Inc
文件頁數： 76/80頁
文件大?。?/td> 0K
描述： IC CLOCK GEN 1.8GHZ VCO 48LFCSP
設計資源： High Performance, Dual Channel IF Sampling Receiver (CN0140)
標準包裝： 750
類型： 時鐘發生器，扇出配送
PLL： 是
輸入： CMOS，LVDS，LVPECL
輸出： CMOS，LVDS，LVPECL
電路數： 1
比率 - 輸入:輸出： 1:12
差分 - 輸入:輸出： 是/是
頻率 - 最大： 1.8GHz
除法器/乘法器： 是/無
電源電壓： 3.135 V ~ 3.465 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-VFQFN 裸露焊盤，CSP
供應商設備封裝： 48-LFCSP-VQ（7x7）
包裝： 帶卷 (TR)
AD9517-4
Data Sheet
Rev. E | Page 78 of 80
CMOS CLOCK DISTRIBUTION
The AD9517 provides four clock outputs (OUT4 to OUT7)
that are selectable as either CMOS or LVDS level outputs.
When selected as CMOS, each output becomes a pair of CMOS
outputs, each of which can be individually turned on or off and
set as noninverting or inverting. These outputs are 3.3 V CMOS
compatible.
Whenever single-ended CMOS clocking is used, some of the
following general guidelines should be used.
Point-to-point nets should be designed such that a driver has
only one receiver on the net, if possible. This allows for simple
termination schemes and minimizes ringing due to possible
mismatched impedances on the net.
Series termination at the source is generally required to provide
transmission line matching and/or to reduce current transients
at the driver. The value of the resistor is dependent on the board
design and timing requirements (typically 10 to 100 is used).
CMOS outputs are also limited in terms of the capacitive load
or trace length that they can drive. Typically, trace lengths of less
than 3 inches are recommended to preserve signal rise/fall times
and preserve signal integrity.
CMOS
10
60.4
(1.0 INCH)
MICROSTRIP
06428-
076
Figure 75. Series Termination of CMOS Output
Termination at the far end of the PCB trace is a second option.
The CMOS outputs of the AD9517 do not supply enough current
to provide a full voltage swing with a low impedance resistive,
far-end termination, as shown in Figure 76. The far-end
termination network should match the PCB trace impedance and
provide the desired switching point. The reduced signal swing
may still meet receiver input requirements in some applications.
This can be useful when driving long trace lengths on less
critical nets.
CMOS
10
50
100
VS
06428-
077
Figure 76. CMOS Output with Far-End Termination
Because of the limitations of single-ended CMOS clocking,
consider using differential outputs when driving high speed
signals over long traces. The AD9517 offers both LVPECL and
LVDS outputs that are better suited for driving long traces
where the inherent noise immunity of differential signaling
provides superior performance for clocking converters.
相關PDF資料
PDF描述
AD9518-0ABCPZ IC CLOCK GEN 6CH 2.8GHZ 48LFCSP
AD9518-1ABCPZ IC CLOCK GEN 6CH 2GHZ 48LFCSP
AD9518-2ABCPZ-RL7 IC CLOCK GEN 6CH 2.2GHZ 48LFCSP
AD9518-3ABCPZ IC CLOCK GEN 6CH 2GHZ 48LFCSP
AD9518-4ABCPZ-RL7 IC CLOCK GEN 6CH 1.8GHZ 48LFCSP
相關代理商/技術參數
參數描述
AD9517-4APCBZ 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Output Clock Generator with Integrated 1.6 GHz VCO
AD9517-4BCPZ 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:IC CLOCK GENERATOR 1.8GHZ LFCSP-48 制造商:Analog Devices 功能描述:IC, CLOCK GENERATOR, 1.8GHZ, LFCSP-48, Clock IC Type:Clock Generator, Frequency:
AD9517-4BCPZ-REEL7 制造商:Analog Devices 功能描述:
AD9518-0 制造商:AD 制造商全稱:Analog Devices 功能描述:6-Output Clock Generator
AD9518-0/PCBZ 制造商:Analog Devices 功能描述:Evaluation Kit For 6-Output Clock Generator With Integrated 2.8 GHZ VCO
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*