- 您現在的位置：買賣IC網 > PDF目錄10060 > AD9246BCPZRL7-105 (Analog Devices Inc)IC ADC 14BIT 105MSPS 48-LFCSP PDF資料下載
參數資料
| 型號： | AD9246BCPZRL7-105 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 105MSPS 48-LFCSP |
| 設計資源： | Using AD8376 to Drive Wide Bandwidth ADCs for High IF AC-Coupled Appls (CN0002) Driving AD9233/46/54 ADCs in AC-Coupled Baseband Appls (CN0051) |
| 標準包裝： | 750 |
| 位數： | 14 |
| 采樣率（每秒）： | 105M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 3 |
| 功率耗散（最大）： | 350mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD9246
Rev. A | Page 23 of 44
SERIAL PORT INTERFACE (SPI)
The AD9246 serial port interface (SPI) allows the user to
configure the converter for specific functions or operations
through a structured register space provided inside the ADC.
This provides the user added flexibility and customization,
depending on the application. Addresses are accessed via the
serial port and can be written to or read from via the port.
Memory is organized into bytes that are further divided into
fields, as documented in the Memory Map section. For detailed
operational information, see the Interfacing to High Speed ADCs
CONFIGURATION USING THE SPI
As summarized in Table 13, three pins define the SPI of this ADC.
The SCLK/DFS pin synchronizes the read and write data
presented to the ADC. The SDIO/DCS dual purpose pin allows
data to be sent and read from the internal ADC memory map
registers. The CSB pin is an active low control that enables or
disables the read and write cycles.
Table 13. Serial Port Interface Pins
Pin Name
Function
SCLK/DFS
SCLK (serial clock) is the serial shift clock in. SCLK
synchronizes serial interface reads and writes.
SDIO/DCS
SDIO (serial data input/output) is a dual purpose
pin. The typical role for this pin is an input and
output, depending on the instruction being sent
and the relative position in the timing frame.
CSB
CSB (chip select bar) is an active low control that
gates the read and write cycles.
The falling edge of the CSB, in conjunction with the rising edge
of the SCLK, determines the start of the framing. Figure 57 and
Table 14 provide examples of the serial timing and its definitions.
Other modes involving the CSB are available. The CSB can be
held low indefinitely to permanently enable the device (this is
called streaming). The CSB can stall high between bytes to allow
for additional external timing. When CSB is tied high, SPI
functions are placed in a high impedance mode. This mode
turns on any SPI pin secondary functions.
During an instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and the length is determined
by the W0 bit and the W1 bit. All data is composed of 8-bit
words. The first bit of each individual byte of serial data
indicates whether a read or write command is issued. This
allows the serial data input/output (SDIO) pin to change
direction from an input to an output.
In addition to word length, the instruction phase determines if
the serial frame is a read or write operation, allowing the serial
port to be used to both program the chip as well as read the
contents of the on-chip memory. If the instruction is a readback
operation, performing a readback causes the serial data input/
output (SDIO) pin to change direction from an input to an
output at the appropriate point in the serial frame.
Data can be sent in MSB- or in LSB-first mode. MSB first is the
default on power up and can be changed via the configuration
register. For more information, see the Interfacing to High Speed
Table 14. SPI Timing Diagram Specifications
Name
Description
tDS
Setup time between data and rising edge of SCLK
tDH
Hold time between data and rising edge of SCLK
tCLK
Period of the clock
tS
Setup time between CSB and SCLK
tH
Hold time between CSB and SCLK
tHI
Minimum period that SCLK should be in a logic
high state
tLO
Minimum period that SCLK should be in a logic
low state
HARDWARE INTERFACE
The pins described in Table 13 comprise the physical interface
between the user’s programming device and the serial port of
the AD9246. The SCLK and CSB pins function as inputs when
using the SPI interface. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during readback.
The SPI interface is flexible enough to be controlled by either
PROM or PIC microcontrollers. This provides the user with the
ability to use an alternate method to program the ADC. One
method is described in detail in the Application Note AN-812,
Microcontroller-based Serial Port Interface Boot Circuit.
When the SPI interface is not used, some pins serve a dual
function. When strapped to AVDD or ground during device
power-on, the pins are associated with a specific function.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO/DCS and SCLK/DFS pins serve as stand-alone
CMOS-compatible control pins. When the device is powered
up, it is assumed that the user intends to use the pins as static
control lines for the output data format and duty cycle stabilizer
(see Table 10). In this mode, the CSB chip select should be
connected to AVDD, which disables the serial port interface.
For more information, see the Interfacing to High Speed ADCs
相關PDF資料 |
PDF描述 |
|---|---|
| LT1739CUE#TR | IC AMP XDSL LINE DVR DUAL 12-DFN |
| VI-BNF-MW-F2 | CONVERTER MOD DC/DC 72V 100W |
| MS3101A22-15S | CONN RCPT 6POS FREE HNG W/SCKT |
| VI-BNF-MW-F1 | CONVERTER MOD DC/DC 72V 100W |
| VI-BND-MW-F4 | CONVERTER MOD DC/DC 85V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9246BCPZRL7-125 | 功能描述:IC ADC 14BIT 125MSPS 48-LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9246BCPZRL7-80 | 制造商:Analog Devices 功能描述:14-BIT, 80 MSPS/105 MSPS/125 MSPS, 1.8 V ANALOG-TO-DIGITAL C - Tape and Reel |
| AD9248 | 制造商:Analog Devices 功能描述:40 MSPS DUAL A/D CONVERTER - Bulk |
| AD9248-20PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 20/40/65 MSPS Dual A/ D Converter |
| AD9248-40PCB | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 20/40/65 MSPS Dual A/ D Converter |
發布緊急采購，3分鐘左右您將得到回復。