參數資料
型號： AD7731BRZ-REEL7
廠商： Analog Devices Inc
文件頁數： 9/44頁
文件大?。?/td> 0K
描述： IC ADC 24BIT SIGMA-DELTA 24-SOIC
標準包裝： 400
位數： 24
采樣率（每秒）： 6.4k
數據接口： DSP，串行，SPI?
轉換器數目： 1
功率耗散（最大）： 125mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 24-SOIC（0.295"，7.50mm 寬）
供應商設備封裝： 24-SOIC W
包裝： 帶卷 (TR)
輸入數目和類型： 3 個差分，單極；3 個差分，雙極；5 個偽差分，單極；5 個偽差分，雙極
配用： EVAL-AD7731EBZ-ND - BOARD EVALUATION FOR AD7731
AD7731
–17–
REV. 0
Bit
Location
Mnemonic
Description
MR12
B/U
Bipolar/Unipolar Bit. A 0 in this bit selects bipolar operation and the output coding is
00...000 for negative full-scale input, 10...000 for zero input and 11...111 for positive full-
scale input. A 1 in this bit selects unipolar operation and the output coding is 00...000 for
zero input and 11...111 for positive full-scale input.
MR11
DEN
Digital Output Enable Bit. With this bit at 1, the AIN3/D1 and AIN4/D0 pins assume their
digital output functions and the output drivers connected to these pins are enabled. In this
mode, the user effectively has two port bits which can be programmed over the serial interface.
MR10–MR9
D1–D0
Digital Output Bits. These bits determine the digital outputs on the AIN3/D1 and AIN4/D0
pins respectively when the DEN bit is a 1. For example, a 1 written to the D1 bit of the
Mode Register (with the DEN bit also a 1) will put a logic 1 on the AIN3/D1 pin. This logic
1 will remain on this pin until a 0 is written to the D1 bit (in which case, the AIN3/D1 pin
goes to a logic 0) or the digital output function is disabled by writing a 0 to the DEN bit.
MR8
WL
Data Word Length Bit. This bit determines the word length of the Data Register. A 0 in this
bit selects 16-bit word length when reading from the data register (i.e.,
RDY returns high
after 16 serial clock cycles in the read operation). A 1 in this bit selects 24-bit word length for
the Data Register.
MR7
HIREF
High Reference Bit. This bit should be set in accordance with the reference voltage which is
being used on the part. If the reference voltage is 2.5 V, the HIREF bit should be set to 0. If
the reference voltage is 5 V, the HIREF bit should be set to a 1. With the HIREF bit set
correctly for the appropriate applied reference voltage, the input ranges are 0 mV to +20 mV,
+40 mV, +80 mV, +160 mV, +320 mV, +640 mV and +1.28 V for unipolar operation and
±20 mV, ±40 mV, ±80 mV, ±160 mV, ±320 mV, ±640 mV and ±1.28 V for bipolar operation.
It is possible for a user with a 2.5 V reference to set the HIREF bit to a 1. In this case, the
part is operating with a 2.5 V reference but assumes it has a 5 V reference. As a result, the
input ranges on the part become 0 mV to +10 mV through 0 mV to +640 mV for unipolar
operation and
±10 mV through ±640 mV for bipolar operation. However, the output noise
from the part (in nV) will remain unchanged so the resolution of the part (in LSBs) will re-
duce by 1.
MR6–MR4
RN2–RN0
Input Range Bits. These bits determine the analog input range for the selected analog input.
The different input ranges are outlined in Table XII. The table is valid for a reference voltage
of 2.5 V with the HIREF bit at 0 or for a reference voltage of 5 V with the HIREF bit at a
logic 1.
Table XII. Input Range Selection
Input Range
RN2
RN1
RN0
B/U Bit = 0
B/U Bit = 1
0
–20 mV to +20 mV
0 mV to +20 mV
0
1
–20 mV to +20 mV
0 mV to +20 mV
0
1
0
–40 mV to +40 mV
0 mV to +40 mV
0
1
–80 mV to +80 mV
0 mV to +80 mV
1
0
–160 mV to +160 mV
0 mV to +160 mV
1
0
1
–320 mV to +320 mV
0 mV to +320 mV
1
0
–640 mV to +640 mV
0 mV to +640 mV
1
–1.28 V to +1.28 V
0 mV to +1.28 V
Power-On/Reset Default
REV. A
相關PDF資料
PDF描述
VI-2WZ-MY CONVERTER MOD DC/DC 2V 20W
VI-2WZ-MW CONVERTER MOD DC/DC 2V 40W
LTC1857IG#PBF IC A/D CONV 8CH 12BIT 28-SSOP
VI-2WY-MY CONVERTER MOD DC/DC 3.3V 33W
VI-2WY-MX CONVERTER MOD DC/DC 3.3V 49.5W
相關代理商/技術參數
參數描述
AD7731EB 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Noise High Throughput 24-Bit Sigma-Delta ADC(411.99 k)
AD7732 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, +-10 V Input Range, High Throughput, 24-Bit SIGMA- ADC
AD7732BRU 功能描述:IC ADC 24BIT 2-CH 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極
AD7732BRU-REEL 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 15.437ksps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel
AD7732BRU-REEL7 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 15.437ksps 24-bit Serial 28-Pin TSSOP T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 15.437KSPS 24BIT SERL 28TSSOP - Tape and Reel 制造商:Rochester Electronics LLC 功能描述:2 DIFF CH :10V INPUT, 28-BIT SD ADC - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*