- 您現在的位置：買賣IC網 > PDF目錄10333 > AD7452BRTZ-REEL7 (Analog Devices Inc)IC ADC 12BIT DIF 555KSPS SOT23-8 PDF資料下載
參數資料
| 型號： | AD7452BRTZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT DIF 555KSPS SOT23-8 |
| 標準包裝： | 3,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 555k |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 7.25mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-8 |
| 供應商設備封裝： | SOT-23-8 |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AD7452
Rev. B | Page 18 of 28
DIGITAL INPUTS
The digital inputs applied to the AD7452 are not limited by the
maximum ratings, which limit the analog limits. Instead the
digital inputs applied, i.e., CS and SCLK, can go to 7 V and are
not restricted by the VDD + 0.3 V limits as on the analog input.
The main advantage of the inputs being unrestricted to the
VDD + 0.3 V limit is that power supply sequencing issues are
avoided. If CS and SCLK are applied before VDD, there is no risk
of latch-up as there would be on the analog inputs if a signal
greater than 0.3 V was applied prior to VDD.
REFERENCE
An external reference source is required to supply the reference
to the AD7452. This reference input can range from 100 mV to
3.5 V. With a 5 V power supply, the specified reference is 2.5 V
and the maximum reference is 3.5 V. With a 3 V power supply,
the specified reference is 2 V and the maximum reference is
2.2 V. In both cases, the reference is functional from 100 mV.
It is important to ensure that when choosing the reference value
for a particular application, the maximum analog input range
(VIN max) is never greater than VDD + 0.3 V to comply with the
maximum ratings of the device. The following two examples
calculate the maximum VREF input that can be used when
operating the AD7452 at a VDD of 5 V and 3 V, respectively.
Example 1
VIN max = VDD + 0.3
VIN max = VREF + VREF/2
If VDD = 5 V, then VIN max = 5.3 V.
Therefore
3 × VREF/2 = 5.3 V
VREF max = 3.5 V
Thus, when operating at VDD = 5 V, the value of VREF can range
from 100 mV to a maximum value of 3.5 V. When VDD = 4.75 V,
VREF max = 3.17 V.
Example 2
VIN max = VDD + 0.3
VIN max = VREF + VREF/2
If VDD = 3 V, then VIN max = 3.3 V.
Therefore
3 × VREF/2 = 3.3 V
VREF max = 2.2 V
Thus, when operating at VDD = 3 V, the value of VREF can range
from 100 mV to a maximum value of 2.2 V. When VDD = 2.7 V,
VREF max = 2 V.
These examples show that the maximum reference applied to
the AD7452 is directly dependent on the value applied to VDD.
The value of the reference sets the analog input span and the
common-mode voltage range. Errors in the reference source
result in gain errors in the AD7452 transfer function and add to
specified full-scale errors on the part. A 0.1 F capacitor should
be used to decouple the VREF pin to GND.
1
AD780
NC
8
2
VIN
NC
7
3
GND
6
4
TEMP
5
OPSEL
TRIM
VOUT
AD7452*
VREF
2.5V
NC
VDD
NC
VDD
NC = NO CONNECT
10nF
0.1
F
0.1
F
0.1
F
03154-A
-033
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 33. Typical VREF Connection Diagram for VDD = 5 V
Table 5. Examples of Suitable Voltage References
Reference
Output
Voltage (V)
Initial
Accuracy (%)
Operating
Current (A)
AD780
2.5/3
0.04
1000
ADR421
2.5
0.04
500
ADR420
2.048
0.05
500
SINGLE-ENDED OPERATION
When supplied with a 5 V power supply, the AD7452 can han-
dle a single-ended input. The design of this part is optimized for
differential operation, so with a single-ended input, perfor-
mance degrades. Linearity degrades by 0.2 LSB typically, the
full-scale errors degrade by 1 LSB typically, and ac performance
is not guaranteed.
To operate the AD7452 in single-ended mode, the VIN+ input is
coupled to the signal source, while the VIN– input is biased to the
appropriate voltage corresponding to the midscale code transi-
tion. This voltage is the common mode, which is a fixed dc
voltage (usually the reference). The VIN+ input swings around
this value and should have a voltage span of 2 × VREF to make
use of the full dynamic range of the part. The input signal
therefore has peak-to-peak values of common mode ± VREF. If
the analog input is unipolar, an op amp in a noninverting unity
gain configuration can be used to drive the VIN+ pin. Because
the ADC operates from a single supply, it is necessary to level
shift ground-based bipolar signals to comply with the input
requirements. An op amp can be configured to rescale and level
shift the ground-based bipolar signal so it is compatible with
the selected input range of the AD7452 (see Figure 34).
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2365HTS8#TRPBF | IC ADC 12BIT 1MSPS TSOT23-8 |
| VI-BW2-MW-S | CONVERTER MOD DC/DC 15V 100W |
| LTC2493CDE#PBF | IC ADC 24BIT DELTA SIG 14-DFN |
| VI-BW1-MW-S | CONVERTER MOD DC/DC 12V 100W |
| VI-2WV-MX-S | CONVERTER MOD DC/DC 5.8V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7453 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Pseudo Differential, 555 kSPS, 12-Bit ADC in an 8-Lead SOT-23 |
| AD7453ART-REEL7 | 制造商:Analog Devices 功能描述: |
| AD7453ARTZ-REEL7 | 功能描述:IC ADC 12BIT DFF 600KSPS SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7453BRT-R2 | 制造商:Analog Devices 功能描述:ADC Single SAR 555ksps 12-bit Serial 8-Pin SOT-23 T/R 制造商:Rochester Electronics LLC 功能描述:12-BIT P/DIFF I/PUT, 600KSPS ADC I.C. - Bulk |
| AD7453BRT-REEL7 | 制造商:Analog Devices 功能描述:ADC Single SAR 555ksps 12-bit Serial 8-Pin SOT-23 T/R |
發布緊急采購，3分鐘左右您將得到回復。