參數資料
型號: AD7452BRTZ-REEL7
廠商: Analog Devices Inc
文件頁數: 10/29頁
文件大?。?/td> 0K
描述: IC ADC 12BIT DIF 555KSPS SOT23-8
標準包裝: 3,000
位數: 12
采樣率(每秒): 555k
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 7.25mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: SOT-23-8
供應商設備封裝: SOT-23-8
包裝: 帶卷 (TR)
輸入數目和類型: 1 個差分,雙極
AD7452
Rev. B | Page 17 of 28
Op Amp Pair
An op amp pair can be used to directly couple a differential
signal to the AD7452. The circuit configurations shown in
Figure 30 and Figure 31 show how a dual op amp can be used to
convert a single-ended signal into a differential signal for both a
bipolar and unipolar input signal, respectively.
The voltage applied to Point A sets up the common-mode
voltage. In both diagrams, it is connected in some way to the
reference, but any value in the common-mode range can be
input here to set up the common mode. The AD8022 is a
suitable dual op amp that could be used in this configuration to
provide differential drive to the AD7452.
Care must be taken when choosing the op amp because the
selection depends on the required power supply and the system
performance objectives. The driver circuits in Figure 30 and
Figure 31 are optimized for dc coupling applications that
require optimum distortion performance.
The differential op amp driver circuit in Figure 30 is configured
to convert and level shift a single-ended, ground-referenced
(bipolar) signal to a differential signal centered at the VREF level
of the ADC.
The circuit configuration shown in Figure 31 converts a
unipolar, single-ended signal into a differential signal.
GND
2
× V
REF p-p
EXTERNAL
VREF
VIN+
VIN–
AD7452
VREF
VDD
V+
V–
V+
V–
220
220
27
390
220
20k
10k
220
27
A
0.1
F
03154-
A-
030
Figure 30. Dual Op Amp Circuit to Convert a Single-Ended
Bipolar Signal into a Differential Signal
VREF
2
× V
REF p-p
EXTERNAL
VREF
VIN+
VIN–
AD7452
VREF
VDD
V+
V–
V+
V–
220
220
27
390
10k
220
27
GND
A
0.1
F
03154-
A-
031
Figure 31. Dual Op Amp Circuit to Convert a Single-Ended
Unipolar Signal into a Differential Signal
RF Transformer
In systems that do not need to be dc-coupled, an RF trans-
former with a center tap offers a good solution for generating
differential inputs. Figure 32 shows how a transformer is used
for single-ended-to-differential conversion. It provides the
benefits of operating the ADC in the differential mode without
contributing additional noise and distortion. An RF transformer
also has the benefit of providing electrical isolation between the
signal source and the ADC. A transformer can be used for most
ac applications. The center tap is used to shift the differential
signal to the common-mode level required; in this case, it is
connected to the reference so the common-mode level is the
value of the reference.
EXTERNAL
VREF (2.5 V)
R
C
VIN+
VIN–
AD7452
3.75V
2.5V
1.25V
3.75V
2.5V
1.25V
VREF
R
03154-A
-032
Figure 32. Using an RF Transformer to Generate Differential Inputs
相關PDF資料
PDF描述
LTC2365HTS8#TRPBF IC ADC 12BIT 1MSPS TSOT23-8
VI-BW2-MW-S CONVERTER MOD DC/DC 15V 100W
LTC2493CDE#PBF IC ADC 24BIT DELTA SIG 14-DFN
VI-BW1-MW-S CONVERTER MOD DC/DC 12V 100W
VI-2WV-MX-S CONVERTER MOD DC/DC 5.8V 75W
相關代理商/技術參數
參數描述
AD7453 制造商:AD 制造商全稱:Analog Devices 功能描述:Pseudo Differential, 555 kSPS, 12-Bit ADC in an 8-Lead SOT-23
AD7453ART-REEL7 制造商:Analog Devices 功能描述:
AD7453ARTZ-REEL7 功能描述:IC ADC 12BIT DFF 600KSPS SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率(每秒):15 數據接口:MICROWIRE?,串行,SPI? 轉換器數目:1 功率耗散(最大):480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN(5x7) 包裝:帶卷 (TR) 輸入數目和類型:16 個單端,雙極;8 個差分,雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494
AD7453BRT-R2 制造商:Analog Devices 功能描述:ADC Single SAR 555ksps 12-bit Serial 8-Pin SOT-23 T/R 制造商:Rochester Electronics LLC 功能描述:12-BIT P/DIFF I/PUT, 600KSPS ADC I.C. - Bulk
AD7453BRT-REEL7 制造商:Analog Devices 功能描述:ADC Single SAR 555ksps 12-bit Serial 8-Pin SOT-23 T/R