- 您現在的位置：買賣IC網 > PDF目錄373891 > AD6655BCPZ-801 (Analog Devices, Inc.) IF Diversity Receiver PDF資料下載
參數資料
| 型號： | AD6655BCPZ-801 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | IF Diversity Receiver |
| 中文描述： | IF分集接收機 |
| 文件頁數： | 60/84頁 |
| 文件大小： | 2012K |
| 代理商： | AD6655BCPZ-801 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁當前第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
AD6655
To avoid this additional DRVDD current, the AD6655 outputs
can be disabled at power-up by taking the OEB pin high. After
the part is placed into LVDS mode via the SPI port, the OEB
pin can be taken low to enable the outputs.
Exposed Paddle Thermal Heat Slug Recommendations
It is mandatory that the exposed paddle on the underside of the
ADC be connected to analog ground (AGND) to achieve the
best electrical and thermal performance. A continuous, exposed
(no solder mask) copper plane on the PCB should mate to the
AD6655 exposed paddle, Pin 0.
The copper plane should have several vias to achieve the lowest
possible resistive thermal path for heat dissipation to flow through
the bottom of the PCB. These vias should be filled or plugged with
nonconductive epoxy.
To maximize the coverage and adhesion between the ADC
and the PCB, a silkscreen should be overlaid to partition the
continuous plane on the PCB into several uniform sections.
This provides several tie points between the ADC and the PCB
during the reflow process. Using one continuous plane with no
partitions guarantees only one tie point between the ADC and
the PCB. See the evaluation board for a PCB layout example.
For detailed information about packaging and PCB layout of
chip scale packages, refer to Application Note AN-772,
A Design
and Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP)
(see
www.analog.com
).
Rev. 0 | Page 60 of 84
CML
The CML pin should be decoupled to ground with a 0.1 μF
capacitor, as shown in Figure 48.
RBIAS
The AD6655 requires that a 10 kΩ resistor be placed between
the RBIAS pin and ground. This resistor sets the master current
reference of the ADC core and should have at least a 1% tolerance.
Reference Decoupling
The VREF pin should be externally decoupled to ground with
a low ESR, 1.0 μF capacitor in parallel with a low ESR, 0.1 μF
ceramic capacitor.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD6655 to keep these signals from transitioning at the converter
inputs during critical sampling periods.
相關PDF資料 |
PDF描述 |
|---|---|
| AD667JN | Microprocessor-Compatible 12-Bit D/A Converter |
| AD667JP | Microprocessor-Compatible 12-Bit D/A Converter |
| AD667KN | Microprocessor-Compatible 12-Bit D/A Converter |
| AD667KP | Microprocessor-Compatible 12-Bit D/A Converter |
| AD668A | 12-Bit Ultrahigh Speed Multiplying D/A Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD6655BCPZRL7-125 | 制造商:Analog Devices 功能描述: |
| AD6655BCPZRL7-150 | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| AD6657 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad IF Receiver |
| AD6657A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Quad IF Receiver |
| AD6657ABBCZ | 功能描述:IC QUAD IF RECEIVER 144BGA RoHS:是 類別:RF/IF 和 RFID >> RF 其它 IC 和模塊 系列:- 標準包裝:100 系列:* |
發布緊急采購，3分鐘左右您將得到回復。