- 您現在的位置：買賣IC網 > PDF目錄8552 > AD5370BCPZ-REEL7 (Analog Devices Inc)IC DAC 16BIT 40CH SERIAL 64LFCSP PDF資料下載
參數資料
| 型號： | AD5370BCPZ-REEL7 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 19/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 16BIT 40CH SERIAL 64LFCSP |
| 產品培訓模塊： | Data Converter Fundamentals DAC Architectures |
| 設計資源： | 40 Channels of Programmable Output Span Using AD5371 (CN0149) |
| 標準包裝： | 750 |
| 設置時間： | 20µs |
| 位數： | 16 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 40 |
| 電壓電源： | 雙 ± |
| 功率耗散（最大）： | 610mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 64-LFCSP-VQ（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 40 電壓，單極；40 電壓，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AD5370
Rev. 0 | Page 25 of 28
POWER SUPPLY DECOUPLING
In any circuit where accuracy is important, careful consideration
of the power supply and ground return layout helps to ensure
the rated performance. The printed circuit board on which the
AD5370 is mounted should be designed so that the analog and
digital sections are separated and confined to certain areas of
the board. If the AD5370 is in a system where multiple devices
require an AGND-to-DGND connection, the connection should
be made at one point only. The star ground point should be
established as close as possible to the device. For supplies with
multiple pins (VSS, VDD, DVCC), it is recommended to tie these
pins together and to decouple each supply once.
The AD5370 should have ample supply decoupling of 10 μF in
parallel with 0.1 μF on each supply located as close to the package
as possible, ideally right up against the device. The 10 μF capacitors
are the tantalum bead type. The 0.1 μF capacitor should have
low effective series resistance (ESR) and low effective series
inductance (ESI)—such as is typical of the common ceramic types
that provide a low impedance path to ground at high frequencies—
to handle transient currents due to internal logic switching.
Digital lines running under the device should be avoided
because they can couple noise onto the device. The analog
ground plane should be allowed to run under the AD5370 to
avoid noise coupling. The power supply lines of the AD5370
should use as large a trace as possible to provide low impedance
paths and reduce the effects of glitches on the power supply line.
Fast-switching digital signals should be shielded with digital
ground to avoid radiating noise to other parts of the board,
and they should never be run near the reference inputs. It is
essential to minimize noise on all VREF lines.
Avoid crossover of digital and analog signals. Traces on opposite
sides of the board should run at right angles to each other. This
reduces the effects of feedthrough through the board. A microstrip
technique is by far the best approach, but it is not always possible
with a double-sided board. In this technique, the component side
of the board is dedicated to ground plane, and signal traces are
placed on the solder side.
As is the case for all thin packages, care must be taken to avoid
flexing the package and to avoid a point load on the surface of
this package during the assembly process.
POWER SUPPLY SEQUENCING
When the supplies are connected to the AD5370, it is important
that the AGND and DGND pins be connected to the relevant
ground plane before the positive or negative supplies are applied.
In most applications, this is not an issue because the ground pins
for the power supplies are connected to the ground pins of the
AD5370 via ground planes. When the AD5370 is used in a hot
swap card, care should be taken to ensure that the ground pins
are connected to the supply grounds before the positive or
negative supply is connected. This is required to prevent currents
from flowing in directions other than toward an analog or
digital ground.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J5P-MW-S | CONVERTER MOD DC/DC 13.8V 100W |
| AD75004KPZ | IC DAC 12BIT QUAD W/BUFF 28-PLCC |
| AD7228LPZ | IC DAC 8BIT OCTAL W/AMP 28-PLCC |
| AD7228KP | IC DAC 8BIT OCTAL W/AMP 28-PLCC |
| AD7846AP | IC DAC 16BIT LC2MOS VOUT 28PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD5370BSTZ | 功能描述:IC DAC 16BIT 40CH SERIAL 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5370BSTZ-REEL | 功能描述:IC DAC 16BIT 40CH SERIAL 64-LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| AD5370BSTZ-U2 | 制造商:Analog Devices 功能描述:40-CH 16-BIT SERIAL BIPOLAR DAC I.C. - Bulk |
| AD5371 | 制造商:AD 制造商全稱:Analog Devices 功能描述:40-Channel, 14-Bit Serial Input, Voltage-Output DAC |
| AD5371BBCZ | 功能描述:IC DAC 14BIT 40CH SER 100-CSPBGA RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散（最大）:941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
發布緊急采購，3分鐘左右您將得到回復。