- 您現在的位置：買賣IC網 > PDF目錄375231 > AD5062 (Analog Devices, Inc.) Full Accurate 14/16 Bit Vout nanoDac Buffered, 3V/5V, Sot 23 PDF資料下載
參數資料
| 型號： | AD5062 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Full Accurate 14/16 Bit Vout nanoDac Buffered, 3V/5V, Sot 23 |
| 中文描述： | 全面準確14/16輸出電壓nanoDAC系列緩沖，3V/5V，索23位 |
| 文件頁數： | 16/17頁 |
| 文件大?。?/td> | 829K |
| 代理商： | AD5062 |
AD5040/5060
Preliminary Technical Data
Rev. PrC | Page 16 of 17
where
D
represents the input code in decimal (0–65535).
With
VDD
= 5 V,
R
1 =
R
2 = 10 kW:
This is an output voltage range of ±5 V with 0000Hex
corresponding to a –5 V output and 3FFF Hex
corresponding to a +5 V output.
Figure 30. Bipolar Operation with the AD5040/AD5060
Using AD5040/AD5060 with an Opto-Isolated
Interface
In process-control applications in industrial environments it is
often necessary to use an opto-isolated interface to protect and
isolate the controlling circuitry from any hazardous common-
mode voltages that may occur in the area where the DAC is
functioning. Because the AD5040/AD5060 uses a three-wire
serial logic interface, the ADuM130Xifamily s an ideal way to
provide digital isolation for the DAC interface.
The ADuM130x isolators provide three independent isolation
channels in a variety of channel configurations and data rates.
They operate across the full range from 2.7V to 5.5V, providing
compatibility with lower voltage systems as well as enabling a
voltage translation functionality across the isolation barrier.
Figure 31. The power supply to the part also needs to be
isolated. This is done by using a transformer. On the DAC side
of the transformer, a +5 V regulator provides the +5 V supply
required for the AD5040/AD5060.
0.1
.
F
+5V
REGULATOR
V
OUT
GND
DIN
SCLK
POWER
10
.
F
V
DD
SCLK
DATA
DAC
SDI
ADMu103x
SDI
V1A
V1B
V1C
VOA
VOB
VOC
Figure 31. AD5040/AD5060 with An Opto-Isolated Interface
Power Supply Bypassing and Grounding
When accuracy is important in a circuit it is helpful to carefully
consider the power supply and ground return layout on the
board. The printed circuit board containing the
AD5040/AD5060 should have separate analog and digital
sections, each having its own area of the board. If the
AD5040/AD5060 is in a system where other devices require an
AGND to DGND connection, the connection should be
made at one point only. This ground point should be
as close as possible to the AD5040/AD5060.
The power supply to the AD5040/AD5060 should be
bypassed with
10 μF and 0.1 μF capacitors. The capacitors should be
physically as close as possible to the device with the 0.1 μF
capacitor ideally right up against the device. The 10 μF
capacitors are the tantalum bead type. It is important that the
0.1 μF capacitor has low Effective Series Resistance (ESR) and
Effective Series Inductance (ESI), e.g., common ceramic types
of capacitors. This 0.1 μF capacitor provides a low impedance
path to ground for high frequencies caused by transient
currents due to internal logic switching.
The power supply line itself should have as large a trace as
possible to provide a low impedance path and reduce glitch
effects on the supply line. Clocks and other fast switching
digital signals should be shielded from other parts of
the board by digital ground. Avoid crossover of digital and
analog signals if possible. When traces cross on opposite sides
of the board, ensure that they run at right angles to each other
to reduce feedthrough effects through the board. The best
board layout technique is the microstrip technique where the
component side of the board is dedicated to the ground plane
only and the signal traces are placed on the solder side.
However, this is not always possible with a two-layer board.
相關PDF資料 |
PDF描述 |
|---|---|
| AD5063 | Full Accurate 14/16 Bit Vout nanoDac Buffered, 3V/5V, Sot 23 |
| AD5062BRJ-1 | Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
| AD5062BRJ-2 | Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
| AD5062BRJ-3 | Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
| AD5063BRM-1 | Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD50621 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Fully Accurate, 16-Bit, Unbuffered VOUT, Quad SPI Interface, 2.7 V to 5.5 V nanoDAC in a TSSOP |
| AD5062ARJZ-1 | 制造商:Analog Devices 功能描述:DAC 1CH R-2R 16BIT 8PIN SOT-23 - Bulk |
| AD5062ARJZ-1500RL7 | 功能描述:IC DAC 16BIT 2.7-5.5V SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| AD5062ARJZ-1REEL7 | 功能描述:IC DAC 16BIT 2.7-5.5V SOT23-8 RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:nanoDAC™ 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| AD5062BRJ-1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Full Accurate 16 Bit Vout nanoDac, 2.7V- 5.5V, in a Sot 23 |
發布緊急采購，3分鐘左右您將得到回復。