- 您現在的位置：買賣IC網 > PDF目錄381232 > AAT1210 (Advanced Analog Technology,lnc.) High Power DC/DC Boost Converter with Optional Dynamic Voltage Programming PDF資料下載
參數資料
| 型號： | AAT1210 |
| 廠商： | Advanced Analog Technology,lnc. |
| 英文描述： | High Power DC/DC Boost Converter with Optional Dynamic Voltage Programming |
| 中文描述： | 高功率DC / DC升壓轉換器可選動態電壓編程 |
| 文件頁數： | 19/23頁 |
| 文件大?。?/td> | 707K |
| 代理商： | AAT1210 |
AAT1210
High Power DC/DC Boost Converter
with Optional Dynamic Voltage Programming
1210.2007.02.1.2
19
Option 2: Dynamic Voltage Control Using SELPin
The output may be dynamically adjusted between
two output voltages by toggling the SEL logic pin.
Output voltages V
OUT(1)
and V
OUT(2)
correspond to
the two output references, FB1 and FB2. Pulling
the SEL logic pin high activates V
OUT(1)
, while
pulling the SEL logic pin low activates V
OUT(2)
.
In addition, the ratio of output voltages V
OUT(2)
/V
OUT(1)
is always less than 2.0, corresponding to a 2X (max-
imum) programmable range.
Option 3: Dynamic Voltage Control Using
S
2
Cwire Interface
The output can be dynamically adjusted by the host
controller to any of 16 pre-set output voltage levels
using the integrated S
2
Cwire interface. The
EN/SET pin serves as the S
2
Cwire interface input.
The SEL pin must be pulled low when using the
S
2
Cwire interface.
S
2
Cwire Serial Interface
AnalogicTech's S
2
Cwire serial interface is a propri-
etary high-speed single-wire interface. The S
2
Cwire
interface records rising edges of the EN/SET input
and decodes into 16 different states. Each state
corresponds to a voltage setting on the FB2 pin, as
shown in Table 6.
S
2
Cwire Output Voltage Programming
The AAT1210 is programmed through the S
2
Cwire
interface according to Table 6. The rising clock
edges received through the EN/SET pin determine
the feedback reference and output voltage set-
point. Upon power-up with the SEL pin low and
prior to S
2
Cwire programming, the default feedback
reference voltage is set to 0.6V.
Table 5: SEL Pin Voltage Control Resistor
Values (1% resistor tolerance).
V
OUT(1)
(SEL = High) (SEL = Low) R1 (k
Ω
)
5.0V
6.0V
7.0V
8.0V
9.0V
10.0V
12.0V
15.0V
16.0V
18.0V
-
-
-
-
-
-
-
-
-
-
9.0V
10.0V
12.0V
15.0V
15.0V
16.0V
18.0V
15.0V
16.0V
18.0V
18.0V
V
OUT(2)
R3 = 4.99k
Ω
R2 (k
Ω
)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0.549
4.02
3.32
1.65
3.01
1.24
0.562
3.01
2.49
1.65
3.32
-
-
-
-
-
-
-
-
-
-
15.8
20.0
24.3
28.0
32.4
36.5
44.2
57.6
61.9
69.8
36.5
45.3
53.6
61.9
69.8
78.7
95.3
121
127
143
36.5
66.5
75
76.8
90.9
76.8
78.7
90.9
93.1
93.1
115
5.0V
6.0V
7.0V
8.0V
9.0V
10.0V
12.0V
15.0V
16.0V
18.0V
5.0V
9.0V
10.0V
10.0V
12.0V
10.0V
10.0V
12.0V
12.0V
12.0V
15.0V
相關PDF資料 |
PDF描述 |
|---|---|
| AAT1210IRN-0.6-T1 | High Power DC/DC Boost Converter with Optional Dynamic Voltage Programming |
| AAT1230 | 18V 100mA Step-Up Converter |
| AAT1230ITP-1-T1 | 18V 100mA Step-Up Converter |
| AAT1230ITP-T1 | 18V 100mA Step-Up Converter |
| AAT1230_0610 | 18V 100mA Step-Up Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AAT1210IRN-0.6-DB1 | 制造商:Advanced Analogic Tech 功能描述:Evaluation Board for AAT1210 High Power DC/DC Boost Converter 制造商:SKYWORKS SOLUTIONS 功能描述:Evaluation Board for AAT1210 High Power DC/DC Boost Converter |
| AAT1210IRN-0.6-T1 | 功能描述:DC/DC 開關控制器 High Power Boost Converter RoHS:否 制造商:ON Semiconductor 輸入電壓: 開關頻率: 輸出電壓: 輸出電流: 輸出端數量: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AAT1217 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:600mA, 1.2MHz, Micropower Synchronous Step-Up Converter |
| AAT1217_08 | 制造商:ANALOGICTECH 制造商全稱:Advanced Analogic Technologies 功能描述:600mA, 1.2MHz, Micropower Synchronous Step-Up Converter |
| AAT1217ICA-1.2-T1 | 功能描述:開關變換器、穩壓器與控制器 1.2MHz ADJ Step Up Converter RoHS:否 制造商:Skyworks Solutions, Inc. 輸出電壓: 輸出電流: 輸出功率: 輸入電壓: 開關頻率: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。