Table 2-8 AC Specifications (5 V PCI Operation) Symbol Parameter Condition Min. Max. Units I
參數資料
型號： A54SX08A-FFG144
廠商： Microsemi SoC
文件頁數： 26/108頁
文件大?。?/td> 0K
描述： IC FPGA SX 12K GATES 144-FBGA
標準包裝： 160
系列： SX-A
LAB/CLB數： 768
輸入/輸出數： 111
門數： 12000
電源電壓： 2.25 V ~ 5.25 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 70°C
封裝/外殼： 144-LBGA
供應商設備封裝： 144-FPBGA（13x13）
SX-A Family FPGAs
2- 4
v5.3
Table 2-8 AC Specifications (5 V PCI Operation)
Symbol
Parameter
Condition
Min.
Max.
Units
IOH(AC)
Switching Current High
0 < VOUT ≤ 1.4
1
–44
–
mA
1.4
≤ V
OUT < 2.4
1, 2
(–44 + (VOUT – 1.4)/0.024)
–
mA
3.1 < VOUT < VCCI
1, 3
–
–
(Test Point)
VOUT = 3.1
3
––142
mA
IOL(AC)
Switching Current Low
VOUT ≥ 2.2
1
95
–
mA
2.2 > VOUT > 0.55
1
(VOUT/0.023)
–
mA
0.71 > VOUT > 0
1, 3
–
–
(Test Point)
VOUT = 0.71
3
–
206
mA
ICL
Low Clamp Current
–5 < VIN ≤ –1
–25 + (VIN + 1)/0.015
–
mA
slewR
Output Rise Slew Rate
0.4 V to 2.4 V load 4
15
V/ns
slewF
Output Fall Slew Rate
2.4 V to 0.4 V load 4
15
V/ns
Notes:
1. Refer to the V/I curves in Figure 2-1 on page 2-5. Switching current characteristics for REQ# and GNT# are permitted to be one half
of that specified here; i.e., half size output drivers may be used on these signals. This specification does not apply to CLK and RST#,
which are system outputs. “Switching Current High” specifications are not relevant to SERR#, INTA#, INTB#, INTC#, and INTD#,
which are open drain outputs.
2. Note that this segment of the minimum current curve is drawn from the AC drive point directly to the DC drive point rather than
toward the voltage rail (as is done in the pull-down curve). This difference is intended to allow for an optional N-channel pull-up.
3. Maximum current requirements must be met as drivers pull beyond the last step voltage. Equations defining these maximums (A
and B) are provided with the respective diagrams in Figure 2-1 on page 2-5. The equation defined maximum should be met by
design. In order to facilitate component testing, a maximum current test point is defined for each side of the output driver.
4. This parameter is to be interpreted as the cumulative edge rate across the specified range, rather than the instantaneous rate at any
point within the transition range. The specified load (diagram below) is optional; i.e., the designer may elect to meet this parameter
with an unloaded output per revision 2.0 of the PCI Local Bus Specification. However, adherence to both maximum and minimum
parameters is now required (the maximum is no longer simply a guideline). Since adherence to the maximum slew rate was not
required prior to revision 2.1 of the specification, there may be components in the market for some time that have faster edge
rates; therefore, motherboard designers must bear in mind that rise and fall times faster than this specification could occur and
should ensure that signal integrity modeling accounts for this. Rise slew rate does not apply to open drain outputs.
Output
Buffer
1/2 in. max.
50 pF
Pin
相關PDF資料
PDF描述
RGM43DTMT CONN EDGECARD 86POS R/A .156 SLD
M1A3P600-1PQG208 IC FPGA 1KB FLASH 600K 208-PQFP
A3P600-1PQG208 IC FPGA 1KB FLASH 600K 208-PQFP
M1A3P600L-PQG208 IC FPGA 1KB FLASH 600K 208-PQFP
A40MX04-PL68I IC FPGA MX SGL CHIP 6K 68-PLCC
相關代理商/技術參數
參數描述
A54SX08A-FFG208 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs
A54SX08A-FFG208A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs
A54SX08A-FFG208B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs
A54SX08A-FFG208I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs
A54SX08A-FFG208M 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SX-A Family FPGAs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*