- 您現在的位置：買賣IC網 > PDF目錄294786 > A1425A-VQG100C FPGA, 310 CLBS, 2500 GATES, 125 MHz, PQFP100 PDF資料下載
參數資料
| 型號： | A1425A-VQG100C |
| 元件分類： | FPGA |
| 英文描述： | FPGA, 310 CLBS, 2500 GATES, 125 MHz, PQFP100 |
| 封裝： | 1 MM HEIGHT, VQFP-100 |
| 文件頁數： | 16/68頁 |
| 文件大?。?/td> | 489K |
| 代理商： | A1425A-VQG100C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
1-197
Accelerator Series FPGAs – ACT 3 Family
Predictable Performance:
Tightest Delay Distributions
Propagation delay between logic modules depends on the
resistive and capacitive loading of the routing tracks, the
interconnect elements, and the module inputs being driven.
Propagation delay increases as the length of routing tracks,
the number of interconnect elements, or the number of
inputs increases.
From a design perspective, the propagation delay can be
statistically correlated or modeled by the fanout (number of
loads) driven by a module. Higher fanout usually requires
some paths to have longer lengths of routing track.
The ACT 3 family delivers the tightest fanout delay
distribution of any FPGA. This tight distribution is achieved
in two ways: by decreasing the delay of the interconnect
elements and by decreasing the number of interconnect
elements per path.
Actel’s patented PLICE antifuse offers a very low
resistive/capacitive interconnect. The ACT 3 family’s
antifuses, fabricated in 0.8 micron m lithography, offer
nominal levels of 200
resistance and 6 femtofarad (fF)
capacitance per antifuse.
The ACT 3 fanout distribution is also tighter than alternative
devices due to the low number of antifuses required per
interconnect
path.
The
ACT
3
family’s
proprietary
architecture limits the number of antifuses per path to only
four, with 90% of interconnects using only two antifuses.
The ACT 3 family’s tight fanout delay distribution offers an
FPGA design environment in which fanout can be traded for
the increased performance of reduced logic level designs.
This also simplifies performance estimates when designing
with ACT 3 devices.
Timing Characteristics
Timing characteristics for ACT 3 devices fall into three
categories: family dependent, device dependent, and design
dependent. The input and output buffer characteristics are
common to all ACT 3 family members. Internal routing delays
are device dependent. Design dependency means actual
delays are not determined until after placement and routing
of the user’s design is complete. Delay values may then be
determined by using the ALS Timer utility or performing
simulation with post-layout delays.
Critical Nets and Typical Nets
Propagation delays are expressed only for typical nets, which
are used for initial design performance evaluation. Critical
net delays can then be applied to the most time-critical
paths. Critical nets are determined by net property
assignment prior to placement and routing. Up to 6% of the
nets in a design may be designated as critical, while 90% of
the nets in a design are typical.
Long Tracks
Some nets in the design use long tracks. Long tracks are
special routing resources that span multiple rows, columns,
or modules.
Long tracks employ three and sometimes four
antifuse connections. This increases capacitance and
resistance, resulting in longer net delays for macros
connected to long tracks. Typically up to 6% of nets in a fully
utilized device require long tracks. Long tracks contribute
approximatley 4 ns to 14 ns delay. This additional delay is
represented statistically in higher fanout (FO=8) routing
delays in the data sheet specifications section.
Timing Derating
ACT 3 devices are manufactured in a CMOS process.
Therefore,
device
performance
varies
according
to
temperature, voltage, and process variations. Minimum
timing parameters reflect maximum operating voltage,
minimum operating temperature, and best-case processing.
Maximum timing parameters reflect minimum operating
voltage, maximum operating temperature, and worst-case
processing.
Table 2 Logic Module and Routing Delay by Fanout (ns)
(Worst-Case Commercial Conditions)
Speed
FO=1
FO=2
FO=3
FO=4
FO=8
ACT 3 –3
2.9
3.2
3.4
3.7
4.8
相關PDF資料 |
PDF描述 |
|---|---|
| A1425A-VQG100I | FPGA, 310 CLBS, 2500 GATES, PQFP100 |
| A1A3-0503-01 | FEMALE-MALE, RF STRAIGHT ADAPTER |
| A1A4-0503-01 | FEMALE-MALE, RF STRAIGHT ADAPTER |
| A1A5-0503-01 | FEMALE-MALE, RF STRAIGHT ADAPTER |
| A3A3-0539-01 | MALE-MALE, RF STRAIGHT ADAPTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1425A-VQG100I | 功能描述:IC FPGA 2500 GATES 100-VQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:ACT™ 3 產品變化通告:XC4000(E,L) Discontinuation 01/April/2002 標準包裝:24 系列:XC4000E/X LAB/CLB數:100 邏輯元件/單元數:238 RAM 位總計:3200 輸入/輸出數:80 門數:3000 電源電壓:4.5 V ~ 5.5 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:120-BCBGA 供應商設備封裝:120-CPGA（34.55x34.55） |
| A1425LK | 功能描述:IC SENSOR HALL EFFECT AC 4-SIP RoHS:否 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1425LK-T | 功能描述:IC SENSOR HALL EFFECT AC 4-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1425-PQ160C | 制造商:Microsemi SOC Products Group 功能描述: |
| A1428AG1 | 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:DIP PLUG PITCH:2.54mm |
發布緊急采購，3分鐘左右您將得到回復。