- 您現在的位置：買賣IC網 > PDF目錄11564 > 78Q8430-100IGTR/F (Maxim Integrated Products)IC LAN MEDIA ACCESS CTLR 100LQFP PDF資料下載
參數資料
| 型號： | 78Q8430-100IGTR/F |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 30/88頁 |
| 文件大小： | 0K |
| 描述： | IC LAN MEDIA ACCESS CTLR 100LQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 控制器類型： | 以太網控制器，MAC/PHY |
| 電源電壓： | 3.3V |
| 電流 - 電源： | 230mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 100-LQFP |
| 供應商設備封裝： | 100-LQFP（14x14） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁
78Q8430 Data Sheet
DS_8430_001
36
Rev. 1.2
STEP 4. Enable the filter. The unicast address filter is enabled by setting the Previous Hit Mask field of
the CAM rule for byte [0] to 0x7F. This step must be done last to prevent an ingressing frame
from matching a partial set of filter rules. All the rules for a filter must be in place before
enabling the filter.
An address filter can be simply activated/deactivated by toggling the value of the Previous Hit Mask field
for the byte [0] CAM rule between 0x7F and 0x00 respectively. The promiscuous mode filter, filter #0,
should not be deactivated in this way.
It is important that STEP 1 deactivates the filter so that no frames are filtered using a partial filter
setting before all relevant rules are written. Step 4 reactivates the filter once the new settings are in
place.
6.7.1.4
Multicast Address Filters
The default CAM rule set supports four multicast address filters. The first, multicast filter #0, serves the same
purpose as the promiscuous mode filter except it applies only to multicast addresses. The last, multicast filter
#3, is the broadcast filter and is reserved for that purpose. The second, multicast filter #1, is the PAUSE filter
and is setup by default to match the PAUSE address. Multicast filter #2 is unused by default and available for
general use. Each filter has two components, the 48-bit address that it matches and a mask that defines
which bits of the address are relevant and which bits are wildcards. Each byte of each address filter has a
CAM rule assigned to it. Table 25 summarizes the association of multicast filter bytes and CAM rules.
Table 25: CAM Rules Associated with Multicast Filter Bytes
Byte [0]
Byte [1]
Byte [2]
Byte [3]
Byte [4]
Byte [5]
M/C Filter #3
0x7F
0x67
0x63
0x4F
0x4B
0x3F
M/C Filter #2
0x7E
0x66
0x62
0x4E
0x4A
0x3E
M/C Filter #1
0x7D
0x65
0x61
0x4D
0x49
0x3D
Note: Bytes are in network transmit order starting with Byte [0].
For an arbitrary multicast filter number N, the following procedure should be used to set the address and
mask values:
STEP 1. Write address and mask byte [0] to CAM rule 0x7C+N as follows.
Reg.
Field
Value to write
CAR
ADDR
0x7C+N
RMR
Data Match
Value of MAC address byte [0]
1
Data Mask
Value of mask byte [0]
1
Previous Hit Match
0x00 to disable the filter
Previous Hit Mask
0x00
RCR
Byte Offset
Retain default: 0x00
Interrupt
Retain default: 0
Control Logic Action
SETMC
Match Control
Retain default: MD
1The LSB of both address byte [0] and mask byte [0] must be set for multicast address filters. If the
LSBs are not set then the address is not multicast and belongs in the unicast filter set.
相關PDF資料 |
PDF描述 |
|---|---|
| GRM2165C1H510JZ01D | CAP CER 51PF 50V 5% NP0 0805 |
| MAX5942BCSE+ | IC IEEE 802.3AF POE SYSTM 16SOIC |
| MAX5984DETI+T | IC CTRLR PD IEEE W/MOSFT 28TQFN |
| PIC16HV785-E/P | IC PIC MCU FLASH 2KX14 20DIP |
| MAX5984AETI+T | IC CTRLR PD IEEE W/MOSFT 28TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 78Q8430-128CGT/F | 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY |
| 78Q8430-128CGTR/F | 制造商:Maxim Integrated Products 功能描述:Ethernet ICs 10/100 Ethernet MAC & PHY |
| 78Q8430-ARM9-EVM | 功能描述:EVALUATION MODULE 78Q8430 ARM9 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| 78Q8430EBST#DB | 功能描述:以太網開發工具 3-in-1 Silicon Delay Line RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| 78Q8430STEM#DB | 功能描述:以太網開發工具 3-in-1 Silicon Delay Line RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。