- 您現在的位置：買賣IC網 > PDF目錄294128 > 72V3684L15PF (INTEGRATED DEVICE TECHNOLOGY INC) 16K X 36 BI-DIRECTIONAL FIFO, 10 ns, PQFP128 PDF資料下載
參數資料
| 型號： | 72V3684L15PF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | FIFO |
| 英文描述： | 16K X 36 BI-DIRECTIONAL FIFO, 10 ns, PQFP128 |
| 封裝： | TQFP-128 |
| 文件頁數： | 7/36頁 |
| 文件大?。?/td> | 418K |
| 代理商： | 72V3684L15PF |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
COMMERCIALTEMPERATURERANGE
IDT72V3684/72V3694/72V36104 3.3V CMOS SyncBiFIFOTM WITH
BUS-MATCHING 16,384 x 36 x 2, 32,768 x 36 x 2, 65 and 536 x 36 x 2
15
Two LOW-to-HIGH transitions of the Almost-Full flag synchronizing clock
are required after a FIFO read for its Almost-Full flag to reflect the new level
of fill. Therefore, the Almost-Full flag of a FIFO containing [16,384/32,768/
65,536-(Y+1)] or less words remains LOW if two cycles of its synchronizing
clock have not elapsed since the read that reduced the number of words in
memory to [16,384/32,768/65,536-(Y+1)]. An Almost-Full flag is set HIGH by
the second LOW-to-HIGH transition of its synchronizing clock after the FIFO
read that reduces the number of words in memory to
[16,384/32,768/65,536-(Y+1)]. A LOW-to-HIGH transition of an Almost-Full
flagsynchronizingclockbeginsthefirstsynchronizationcycleifitoccursattime
tSKEW2 or greater after the read that reduces the number of words in memory
to [16,384/32,768/65,536-(Y+1)]. Otherwise, the subsequent synchronizing
clock cycle may be the first synchronization cycle (see Figure 25 and 26).
MAILBOX REGISTERS
Each FIFO has a 36-bit bypass register to pass command and control
information between Port A and Port B without putting it in queue. The Mailbox
select (MBA, MBB) inputs choose between a mail register and a FIFO for a
port data transfer operation. The usable width of both the Mail1 and Mail2
registers matches the selected bus size for Port B.
A LOW-to-HIGH transition on CLKA writes data to the Mail 1 Register when
a Port A write is selected by
CSA, W/RA, and ENA with MBA HIGH. If the
selectedPortBbussizeisalso36bits,thentheusablewidthoftheMail1register
employs data lines A0-A35. If the selected Port B bus size is 18 bits, then the
usable width of the Mail1 Register employs data lines A0-A17. (In this case,
A18-A35 are don’t care inputs.) If the selected Port B bus size is 9 bits, then
the usable width of the Mail1 Register employs data lines A0-A8. (In this case,
A9-A35 are don’t care inputs.)
ALOW-to-HIGHtransitiononCLKBwritesB0-B35datatotheMail2Register
when a Port B write is selected by
CSB, W/RB, and ENB with MBB HIGH. If
the selected Port B bus size is also 36 bits, then the usable width of the Mail2
employs data lines B0-B35. If the selected Port B bus size is 18 bits, then the
usable width of the Mail2 Register employs data lines B0-B17. (In this case,
B18-B35 are don’t care inputs.) If the selected Port B bus size is 9 bits, then
the usable width of the Mail2 Register employs data lines B0-B8. (In this case,
B9-B35 are don’t care inputs.)
Writing data to a mail register sets its corresponding flag (
MBF1 or MBF2)
LOW.AttemptedwritestoamailregisterareignoredwhilethemailflagisLOW.
When data outputs of a port are active, the data on the bus comes from the
FIFO output register when the port Mailbox select input is LOW and from the
mail register when the port Mailbox select input is HIGH.
The Mail1 Register Flag (
MBF1)issetHIGH bya LOW-to-HIGH transition
on CLKB when a Port B read is selected by
CSB, W/RB, and ENB with MBB
HIGH. For a 36-bit bus size, 36 bits of mailbox data are placed on B0-B35.
For an 18-bit bus size, 18 bits of mailbox data are placed on B0-B17. (In this
case, B18-B35 are indeterminate.) For a 9-bit bus size, 9 bits of mailbox data
are placed on B0-B8. (In this case, B9-B35 are indeterminate.)
The Mail2 Register Flag (
MBF2)issetHIGHbya LOW-to-HIGHtransition
on CLKA when a Port A read is selected by
CSA, W/RA, and ENA with MBA
HIGH.
For a 36-bit bus size, 36 bits of mailbox data are placed on A0-A35. For
an 18-bit bus size, 18 bits of mailbox data are placed on A0-A17. (In this case,
A18-A35 are indeterminate.) For a 9-bit bus size, 9 bits of mailbox data are
placed on A0-A8. (In this case, A9-A35 are indeterminate.)
The data in a mail register remains intact after it is read and changes only
whennewdataiswrittentotheregister.TheEndianselectfeaturehasnoeffect
on mailbox data. For mail register and Mail Register Flag timing diagrams, see
Figure 27 and 28.
BUS SIZING
The Port B bus can be configured in a 36-bit long word, 18-bit word, or 9-
bit byte format for data read from FIFO1 or written to FIFO2. The levels
applied to the Port B Bus Size select (SIZE) and the Bus-Match select (BM)
determine the Port B bus size. These levels should be static throughout FIFO
operation. Both bus size selections are implemented at the completion of
Master Reset, by the time the Full/Input Ready flag is set HIGH, as shown in
Figure 2.
Two different methods for sequencing data transfer are available for Port
B when the bus size selection is either byte- or word-size. They are referred
to as Big-Endian (most significant byte first) and Little-Endian (least significant
bytefirst).ThelevelappliedtotheBig-Endianselect(BE)inputduringtheLOW-
to-HIGH transition of
MRS1andMRS2selectstheendianmethodthatwillbe
active during FIFO operation. BE is a don’t care input when the bus size
selected for Port B is long word. The endian method is implemented at the
completion of Master Reset, by the time the Full/Input Ready flag is set HIGH,
as shown in Figure 2.
Only 36-bit long word data is written to or read from the two FIFO memories
on the IDT72V3684/72V3694/72V36104. Bus-matching operations are done
after data is read from the FIFO1 RAM and before data is written to the FIFO2
RAM. These bus-matching operations are not available when transferring
data via mailbox registers. Furthermore, both the word- and byte-size bus
selections limit the width of the data bus that can be used for mail register
operations. In this case, only those byte lanes belonging to the selected word-
or byte-size bus can carry mailbox data. The remaining data outputs will be
indeterminate. The remaining data inputs will be don’t care inputs. For
example, when a word-size bus is selected, then mailbox data can be
transmitted only between A0-A17 and B0-B17. When a byte-size bus is
selected, then mailbox data can be transmitted only between A0-A8 and B0-
B8. (See Figures 27 and 28).
BUS-MATCHING FIFO1 READS
Data is read from the FIFO1 RAM in 36-bit long word increments. If a long
word bus size is implemented, the entire long word immediately shifts to the
FIFO1 output register. If byte or word size is implemented on Port B, only the
firstoneortwobytesappearontheselectedportionoftheFIFO1outputregister,
with the rest of the long word stored in auxiliary registers. In this case,
subsequent FIFO1 reads output the rest of the long word to the FIFO1 output
register in the order shown by Figure 2.
When reading data from FIFO1 in byte or word format, the unused B0-B35
outputsareindeterminate.
BUS-MATCHING FIFO2 WRITES
DataiswrittentotheFIFO2RAMin36-bitlongwordincrements.Datawritten
toFIFO2withabyteorwordbussizestorestheinitialbytesorwordsinauxiliary
registers. The CLKB rising edge that writes the fourth byte or the second word
of long word to FIFO2 also stores the entire long word in the FIFO2 memory.
The bytes are arranged in the manner shown in Figure 2.
WhenwritingdatatoFIFO2inbyteorwordformat,theunusedB0-B35inputs
are don't care inputs.
相關PDF資料 |
PDF描述 |
|---|---|
| 72V845L15PFI8 | 4K X 18 BI-DIRECTIONAL FIFO, 10 ns, PQFP128 |
| 72V805L15PFI9 | 256 X 18 BI-DIRECTIONAL FIFO, 10 ns, PQFP128 |
| 72V805L15PF8 | 256 X 18 BI-DIRECTIONAL FIFO, 10 ns, PQFP128 |
| 7305-0-15-15-47-14-04-0 | BRASS, GOLD FINISH, PCB TERMINAL |
| 7305-0-15-15-47-01-04-0 | BRASS, GOLD FINISH, PCB TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 72V3690L10PF | 功能描述:先進先出 RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| 72V3690L10PF8 | 制造商:Integrated Device Technology Inc 功能描述:FIFO Mem Sync Dual Depth/Width Uni-Dir 32K x 36 128-Pin TQFP T/R 制造商:Integrated Device Technology Inc 功能描述:FIFO SYNC DUAL DEPTH/WIDTH UNI-DIR 32KX36 128TQFP - Tape and Reel |
| 72V3690L15PF | 功能描述:先進先出 RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| 72V3690L15PF8 | 制造商:Integrated Device Technology Inc 功能描述:FIFO Mem Sync Dual Depth/Width Uni-Dir 32K x 36 128-Pin TQFP T/R 制造商:Integrated Device Technology Inc 功能描述:FIFO SYNC DUAL DEPTH/WIDTH UNI-DIR 32KX36 128TQFP - Tape and Reel |
| 72V3690L15PFI | 功能描述:先進先出 RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
發布緊急采購，3分鐘左右您將得到回復。