- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6532D-IGTR/F (TERIDIAN SEMICONDUCTOR CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6532D-IGTR/F |
| 廠商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 62/120頁 |
| 文件大?。?/td> | 2477K |
| 代理商： | 71M6532D-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
Data Sheet 71M6531D/F-71M6532D/F
FDS 6531/6532 005
46
2005-2010 TERIDIAN Semiconductor Corporation
v1.3
Section 4.1 I/O RAM and SFR Map – Functional Order. The LCD drivers are supported by the four common
pins (COM0 – COM3).
1.5.11 LCD Drivers – 71M6532D/F
The 71M6532D/F contains a total of 67 dedicated and multiplexed LCD drivers, which are grouped as
follows:
15 dedicated LCD segment drivers (SEG0 to SEG2, SEG8, SEG12 - SEG18, SEG20 – SEG23)
4 drivers multiplexed with the SPI port (SEG3 to SEG6)
2 drivers multiplexed with MUX_SYNC (SEG7) or CKTEST (SEG19)
3 drivers multiplexed with the ICE interface (SEG9 to SEG11)
43 multi-use LCD/DIO pins described in Section 1.5.8 Digital I/O – 71M6532D/F.
With a minimum of 15 driver pins always available and a total of 67 driver pins in the maximum configuration,
the device is capable of driving between 60 to 268 pixels of an LCD display with 25% duty cycle. At eight
pixels per digit, this corresponds to 7.5 to 33.5 digits.
For each multi-use pin, the corresponding LCD_BITMAP[ ] bit (see Section 1.5.8 Digital I/O – 71M6532D/F),
is used to select the pin for DIO or LCD operation. The mapping of the LCD_BITMAP[ ] bits is specified in
Section 4.1 I/O RAM and SFR Map – Functional Order. The LCD drivers are supported by the four common
pins (COM0 – COM3).
1.5.12 LCD Drivers – Common Characteristics for 71M6531D/F and 71M6532D/F
The LCD interface is flexible and can drive 7-segment digits, 14-segment digits or enunciator symbols.
The LCD bias may be compensated for temperature using the LCD_DAC[2:0] bits in I/O RAM. The bias
may be adjusted from 1.4 V below the 3.3 V supply (V3P3SYS in mission mode and brownout modes,
VBAT in LCD mode). When the LCD_DAC[2:0] bits are set to 000, the DAC is bypassed and powered
down. This can be used to reduce current in LCD mode.
Segment drivers SEG18 and SEG19 can be configured to blink at either 0.5 Hz or 1 Hz. The blink rate is
controlled by LCD_Y. There can be up to four pixels/segments connected to each of these drivers.
LCD_BLKMAP18[3:0] and LCD_BLKMAP19[3:0] identify which pixels, if any, are to blink. The most
significant bit corresponds to COM3, the least significant to COM0.
1.5.13 Battery Monitor
The battery voltage is measured by the ADC during alternative MUX frames if the BME (Battery Measure
Enable) bit is set. While BME is set, an on-chip 45 k
load resistor is applied to the battery and a scaled
fraction of the battery voltage is applied to the ADC input. After each alternative MUX frame, the result of
the ADC conversion is available at RAM address 0x0B. BME is ignored and assumed zero when system
power is not available.
If VBAT is connected to a drained battery or disconnected, a battery test that sets BME may drain
VBAT’s supply and cause the oscillator to stop. A stopped oscillator may force the device to reset.
Therefore, an unexpected reset during a battery test should be interpreted as a battery failure.
Battery measurement is not very linear but is very reproducible if properly calibrated. The best way to
perform the calibration is to set the battery input to the desired failure voltage and then have the MPU
firmware record that measurement. After this, the battery measurement logic may use the recorded value
as the battery failure limit. The same value can also be a calibration offset for any battery voltage display.
See Section 5.4.4 Battery Monitor for details regarding the ADC LSB size and the conversion accuracy.
1.5.14 EEPROM Interface
The 71M6531D/F and 71M6532D/F provide hardware support for either a two-pin or a three-wire (-wire)
type of EEPROM interface. The interfaces use the EECTRL and EEDATA registers for communication.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6532F-IGT/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6531D-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6531F-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6531F-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532D-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6532F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Energy Meter IC |
| 71M6532F-IGT/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGT/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGTR/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGTR/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。