- 您現在的位置：買賣IC網 > PDF目錄68811 > 71M6532D-IGTR/F (TERIDIAN SEMICONDUCTOR CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6532D-IGTR/F |
| 廠商： | TERIDIAN SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 29/120頁 |
| 文件大?。?/td> | 2477K |
| 代理商： | 71M6532D-IGTR/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
Data Sheet 71M6531D/F-71M6532D/F
FDS 6531/6532 005
16
2005-2010 TERIDIAN Semiconductor Corporation
v1.3
1.3.1
Meter Equations
The 71M6531D/F and 71M6532D/F provide hardware assistance to the CE in order to support various
meter equations. This assistance is controlled through I/O RAM location EQU[2:0] (equation assist). The
Compute Engine (CE) firmware for residential configurations implements the equations listed in Table 5.
EQU[2:0] specifies the equation to be used based on the number of phases used for metering.
Table 5: Meter Equations
EQU[2:0]
Description
Watt and VAR Formula
Mux
Sequence
ALT Mux
Sequence
Element
0
Element
1
Element
2
0
1 element, 2 W,
1
φ with neutral
current sense
VA IA
VA IB
N/A
Sequence is
programmable
with
SLOTn_SEL[3:0]
Sequence is
programmable with
SLOTn_ALTSEL[3:0]
1
1 element, 3 W,
1
φ
VA(IA-
IB)/2
N/A
2
2 element, 3 W,
3
φ Delta
VA IA
VB IB
N/A
Not all CE codes support all equations.
1.3.2
Real-Time Monitor
The CE contains a Real-Time Monitor (RTM), which can be programmed to monitor four selectable XRAM
locations at full sample rate. The four monitored locations are serially output to the TMUXOUT pin via the
digital output multiplexer at the beginning of each CE code pass. The RTM can be enabled and disabled
with the RTM_E bit. The RTM output is clocked by CKTEST (pin SEG19/CKTEST), with the clock output
enabled by setting CKOUT_E = 1. Each RTM word is clocked out in 35 cycles and contains a leading flag
bit. See Figure 20 for the RTM output format. RTM is low when not in use.
1.3.3
Pulse Generators
The 71M6531D/F and 71M6532D/F provide four pulse generators, RPULSE, WPULSE, XPULSE and
YPULSE, as well as increased hardware support for the two original pulse generators (RPULSE and
WPULSE). The pulse generators can be used to output CE status indicators, SAG for example, to DIO pins.
The polarity of the pulses may be inverted with the PLS_INV bit. When this bit is set, the pulses are active
high, rather than the more usual active low. PLS_INV inverts all the pulse outputs.
XPULSE and YPULSE
Pulses generated by the CE may be exported to the XPULSE and YPULSE pulse outputs. Pins DIO8
and DIO9 are used for these pulses. Generally, the XPULSE and YPULSE outputs are updated once on
each pass of the CE code, resulting in a pulse frequency up to a maximum of 1260Hz (assuming a MUX
frame is 13 CK32 cycles).
The YPULSE pin can be used by the CE code to generate interrupts based on sag events. This method
is faster than checking the sag bits by the MPU at every CE_BUSY interrupt. See Section 4.3.6 CE Status
and Control for details.
RPULSE and WPULSE
During each CE code pass, the hardware stores exported WPULSE AND RPULSE sign bits in an 8-bit
FIFO and outputs them at a specified interval. This permits the CE code to calculate the RPULSE and
WPULSE outputs at the beginning of its code pass and to rely on hardware to spread them over the MUX
frame. The FIFO is reset at the beginning of each MUX frame. The PLS_INTERVAL register controls the
delay to the first pulse update and the interval between subsequent updates. Its LSB is 4 CK_FIR cycles.
If zero, the FIFO is deactivated and the DFFs are updated immediately. Thus, NINTERVAL is
4 * PLS_INTERVAL.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6532F-IGT/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6531D-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6531F-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6531F-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532D-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6532F | 制造商:TERIDIAN 制造商全稱:TERIDIAN 功能描述:Energy Meter IC |
| 71M6532F-IGT/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGT/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGTR/F | 功能描述:計量片上系統 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6532F-IGTR/F1 | 功能描述:計量片上系統 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。