參數資料
型號: 4559
廠商: Renesas Technology Corp.
英文描述: SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
中文描述: 單芯片4位微機的CMOS
文件頁數: 85/148頁
文件大?。?/td> 1732K
代理商: 4559
Rev.1.04
Aug 23, 2007
Page 41 of 146
REJ03B0188-0104
4559 Group
WATCHDOG TIMER
Watchdog timer provides a method to reset the system when a
program run-away occurs. Watchdog timer consists of timer
WDT(16-bit binary counter), watchdog timer enable flag (WEF),
and watchdog timer flags (WDF1, WDF2).
The timer WDT downcounts the instruction clocks as the count
source from “FFFF16” after system is released from reset.
After the count is started, when the timer WDT underflow occurs
(after the count value of timer WDT reaches “000016,” the next
count pulse is input), the WDF1 flag is set to “1.” If the WRST
instruction is never executed until the timer WDT underflow
occurs (until timer WDT counts 65534), WDF2 flag is set to “1,”
and the RESET pin outputs “L” level to reset the microcomputer.
Execute the WRST instruction at each period of 65534 machine
cycle or less by software when using watchdog timer to keep the
microcomputer operating normally.
When the WEF flag is set to “1” after system is released from
reset, the watchdog timer function is valid.
When the DWDT instruction and the WRST instruction are
executed continuously, the WEF flag is cleared to “0” and the
watchdog timer function is invalid.
The WEF flag is set to “1” at system reset or RAM back-up
mode.
The WRST instruction has the skip function. When the WRST
instruction is executed while the WDF1 flag is “1”, the WDF1
flag is cleared to “0” and the next instruction is skipped.
When the WRST instruction is executed while the WDF1 flag is
“0”, the next instruction is not skipped.
The skip function of the WRST instruction can be used even
when the watchdog timer function is invalid.
Fig 40. Watchdog timer function
(1) Reset released
65534 count
(Note)
(4)
(2)
(3) WRST instruction
executed (skip occurrence)
(5) System reset
FFFF16
000016
Value of 16-bit timer (WDT)
WDF1 flag
WDF2 flag
RESET pin output
(1) After system is released from reset (= after program is started), timer WDT starts count down.
(2) When timer WDT underflow occurs, WDF1 flag is set to “1.”
(3) When the WRST instruction is executed while the WDF1 flag is “1”, WDF1 flag is cleared to “0,” the next
instruction is skipped.
(4) When timer WDT underflow occurs while WDF1 flag is “1,” WDF2 flag is set to “1” and the watchdog reset
signal is output.
(5) The output transistor of RESET pin is turned “ON” by the watchdog reset signal and system reset is
executed.
Note: The number of count is equal to the number of machine cycle because the count source of watchdog timer
is the instruction clock.
相關PDF資料
PDF描述
456700000 Terminal Block; Leaded Process Compatible:Yes
457000000 Cross Connector; Number of Positions:10; Current Rating:24 VA
45714-0003 Edge Connector,PCB Mnt,RECEPT,8 Contacts,0.507 Pitch,COMPLIANT FIT Terminal,GUIDE SLOT
45714-0001 Card Edge Connector; No. of Contacts:4; Pitch Spacing:0.508"; Contact Termination:Press-Fit; Body Material:LCP Liquid Crystal Polymer, Glass-filled; Mounting Type:Through Hole; Series:45714; Color:Black; Voltage Rating:250V RoHS Compliant: Yes
45714-0002 Card Edge Connector; No. of Contacts:6; Pitch Spacing:0.508"; Contact Termination:Press-Fit; Body Material:LCP Liquid Crystal Polymer, Glass-filled; Mounting Type:Through Hole; Series:45714; Color:Black; Voltage Rating:250V RoHS Compliant: Yes
相關代理商/技術參數
參數描述
4559_08 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Standard Characteristics
45-590 制造商:GC Electronics 功能描述:Conn D-Subminiature Adapter F/F 9/15 POS ST 1 Port
45-590 4/PK 功能描述:電纜組件 DB-9F DB-15F HI DEN RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規(AWG):20, 28 長度:0.305 m 顏色:Black, Red
4-5-5906 功能描述:TAPE 5906 VHB FOAM 4" X 5YD 制造商:3m (tc) 系列:* 零件狀態:有效 標準包裝:1
4-5-5907 功能描述:TAPE 5907 VHB FOAM 4" X 5YD 制造商:3m (tc) 系列:* 零件狀態:有效 標準包裝:1