- 您現在的位置：買賣IC網 > PDF目錄371435 > 28F800C2 (Intel Corp.) 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) PDF資料下載
參數資料
| 型號： | 28F800C2 |
| 廠商： | Intel Corp. |
| 英文描述： | 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) |
| 中文描述： | 2.4V的高級啟動塊閃存（2.4V的高級引導塊閃速存儲器） |
| 文件頁數： | 15/56頁 |
| 文件大?。?/td> | 283K |
| 代理商： | 28F800C2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
E
28F800C2, 28F160C2
15
PRELIMINARY
Table 6. Command Codes and Descriptions
Code
Device Mode
Description
FF
Read Array
Places device in read array mode, such that array data will be output on the
data pins.
40
Program
Set-Up
This is a two-cycle command. The first cycle prepares the CUI for a program
operation. The second cycle latches addresses and data information and
initiates the WSM to execute the Program algorithm. The flash outputs status
register data when CE# or OE# is toggled. A Read Array command is required
after programming to read array data. See Section 3.2.5.
20
Erase
Set-Up
Prepares the CUI for the Erase Confirm command. If the next command is not
an Erase Confirm command, then the CUI will (a) set both SR.4 and SR.5 of the
status register to a
“1,” (b) place the device into the read status register mode,
and (c) wait for another command. See Section 3.2.6.
D0
Erase Confirm
Program/Erase
Resume
Unlock Block
If the previous command was an Erase Set-Up command, then the CUI will
close the address and data latches, and begin erasing the block indicated on the
address pins. During program/erase, the device will respond only to the Read
Status Register, Program Suspend and Erase Suspend commands and will
output status register data when CE# or OE# is toggled.
If a program or erase operation was previously suspended, this command will
resume that operation.
If the previous command was Configuration Set-Up, the CUI will latch the
address and unlock the block indicated on the address pins. If the block had
been previously set to Lock-Down, this operation will have no effect. (Sect. 3.3)
B0
Program
Suspend
Erase
Suspend
Issuing this command will begin to suspend the currently executing
program/erase operation. The status register will indicate when the operation
has been successfully suspended by setting either the program suspend (SR.2)
or erase suspend (SR.6) and the WSM status bit (SR.7) to a “1” (ready). The
WSM will continue to idle in the SUSPEND state, regardless of the state of all
input control pins except RP#, which will immediately shut down the WSM and
the remainder of the chip if RP# is driven to V
IL
. See Sections 3.2.5.1 and
3.2.6.1.
70
Read Status
Register
This command places the device into read status register mode. Reading the
device will output the contents of the status register, regardless of the address
presented to the device. The device automatically enters this mode after a
program or erase operation has been initiated. See Section 3.2.3.
50
Clear Status
Register
The WSM can set the block lock status (SR.1) , V
PP
Status (SR.3), program
status (SR.4), and erase status (SR.5) bits in the status register to “1,” but it
cannot clear them to “0.” Issuing this command clears those bits to “0.”
90
Read
Configuration
Puts the device into the read configuration mode, so that reading the device will
output the manufacturer/device codes or block lock status. Section 3.2.2.
60
Configuration
Set-Up
Prepares the CUI for changes to the device configuration, such as block locking
changes. If the next command is not Block Unlock, Block Lock, or Block Lock-
Down, then the CUI will set both the program and erase status register bits to
indicate a command sequence error. See Section 3.3.
01
Lock-Block
If the previous command was Configuration Set-Up, the CUI will latch the
address and lock the block indicated on the address pins. (Section 3.3)
相關PDF資料 |
PDF描述 |
|---|---|
| 28F160S3 | 3 V FlashFile Memory(3 V FlashFile 存儲器) |
| 28F320S3 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
| 28F160S5 | 5 V FlashFile Memory(5 V FlashFile 存儲器) |
| 28F320S5 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
| 28F200B5 | 5V Boot Block Flash Memory(5 V 引導塊閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F800C3 | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:Advanced+ Boot Block Flash |
| 28F800CE-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Boot Flash |
| 28F800CV-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-MBIT (512K X 16. 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F800F3 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:FAST BOOT BLOCK FLASH MEMORY FAMILY 8 AND 16 MBIT |
| 28FAN2500_AAA3A862 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。