- 您現在的位置：買賣IC網 > PDF目錄371435 > 28F800C2 (Intel Corp.) 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) PDF資料下載
參數資料
| 型號： | 28F800C2 |
| 廠商： | Intel Corp. |
| 英文描述： | 2.4V Advanced+ Boot Block Flash Memory(2.4V高級引導塊閃速存儲器) |
| 中文描述： | 2.4V的高級啟動塊閃存（2.4V的高級引導塊閃速存儲器） |
| 文件頁數： | 14/56頁 |
| 文件大?。?/td> | 283K |
| 代理商： | 28F800C2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
28F800C2, 28F160C2
E
14
PRELIMINARY
3.2.6.1
Suspending and Resuming Erase
Since an erase operation requires on the order of
seconds to complete, an Erase Suspend command
is provided to allow erase-sequence interruption in
order to read data from or program data to another
block in memory. Once the erase sequence is
started, writing the Erase Suspend command to the
CUI
suspends
the
erase
predetermined point in the erase algorithm. The
status register will indicate if/when the erase
operation has been suspended. Erase suspend
latency is specified by t
WHRH2
/t
EHRH2
.
sequence
at
a
A Read Array/Program command can now be
written to the CUI to read/program data from/to
blocks other than that which is suspended. This
nested Program command can subsequently be
suspended to read yet another location. The only
valid commands while erase is suspended are
Read Status Register, Read Configuration, Read
Query, Program Setup, Program Resume, Erase
Resume, Lock Block, Unlock Block and Lock-Down
Block. During erase suspend mode, the chip can be
placed in a pseudo-standby mode by taking CE# to
V
IH
. This reduces active current consumption.
Erase Resume continues the erase sequence when
CE# = V
IL
. As with the end of a standard erase
operation, the status register must be read and
cleared before the next instruction is issued.
Table 5. Command Bus Definitions
First Bus Cycle
Second Bus Cycle
Command
Notes
Oper
Addr
Data
Oper
Addr
Data
Read Array
4
Write
X
FFH
Read Configuration
2, 4
Write
X
90H
Read
IA
ID
Read Query
2, 4
Write
X
98H
Read
QA
QD
Read Status Register
4
Write
X
70H
Read
X
SRD
Clear Status Register
4
Write
X
50H
Program
3,4
Write
X
40H/10H
Write
PA
PD
Block Erase/Confirm
4
Write
X
20H
Write
BA
D0H
Program/Erase Suspend
4
Write
X
B0H
Program/Erase Resume
4
Write
X
D0H
Lock Block
4
Write
X
60H
Write
BA
01H
Unlock Block
4
Write
X
60H
Write
BA
D0H
Lock-Down Block
4
Write
X
60H
Write
BA
2FH
Protection Program
4
Write
X
C0H
Write
PA
PD
X =
Don’t Care
SRD = Status Reg. Data
NOTES:
1.
Bus operations are defined in Table 3.
2.
Following the Read Configuration or Read Query commands, read operations output device configuration or CFI query
information, respectively. See Section 3.2.2 and 3.2.4.
3.
Either 40H or 10H command is valid, but the Intel standard is 40H.
4.
When writing commands, the upper data bus [DQ
8
–DQ
15
] should be either V
IL
or V
IH
, to minimize current draw.
PA = Prog Addr
PD = Prog Data
BA = Block Addr
IA
=
Identifier Addr.
ID = Identifier Data
QA = Query Addr.
QD = Query Data
相關PDF資料 |
PDF描述 |
|---|---|
| 28F160S3 | 3 V FlashFile Memory(3 V FlashFile 存儲器) |
| 28F320S3 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
| 28F160S5 | 5 V FlashFile Memory(5 V FlashFile 存儲器) |
| 28F320S5 | 3 V、32MB FlashFile Memory(3 V、32M位FlashFile 存儲器) |
| 28F200B5 | 5V Boot Block Flash Memory(5 V 引導塊閃速存儲器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 28F800C3 | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:Advanced+ Boot Block Flash |
| 28F800CE-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Boot Flash |
| 28F800CV-T/B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-MBIT (512K X 16. 1024K X 8) SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| 28F800F3 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:FAST BOOT BLOCK FLASH MEMORY FAMILY 8 AND 16 MBIT |
| 28FAN2500_AAA3A862 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。