- 您現在的位置：買賣IC網 > PDF目錄371370 > 2184 (Analog Devices, Inc.) DSP Microcomputer PDF資料下載
參數資料
| 型號： | 2184 |
| 廠商： | Analog Devices, Inc. |
| 元件分類： | 數字信號處理 |
| 英文描述： | DSP Microcomputer |
| 中文描述： | DSP微機 |
| 文件頁數： | 7/31頁 |
| 文件大?。?/td> | 213K |
| 代理商： | 2184 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
ADSP-2184
–7–
REV. 0
Clock Signals
The ADSP-2184 can be clocked by either a crystal or a TTL-
compatible clock signal.
The CLKIN input cannot be halted, changed during operation
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information, refer to Chapter 9,
ADSP-2100 Family User’s Manual
,
Third Edition
, for detailed
information on this power-down feature.
If an external clock is used, it should be a TTL-compatible
signal running at half the instruction rate. The signal is con-
nected to the processor’s CLKIN input. When an external clock
is used, the XTAL input must be left unconnected.
The ADSP-2184 uses an input clock with a frequency equal to
half the instruction rate; a 20.00 MHz input clock yields a 25 ns
processor cycle (which is equivalent to 40 MHz). Normally,
instructions are executed in a single processor cycle. All device
timing is relative to the internal instruction clock rate, which is
indicated by the CLKOUT signal when enabled.
Because the ADSP-2184 includes an on-chip oscillator circuit,
an external crystal may be used. The crystal should be con-
nected across the CLKIN and XTAL pins, with two capacitors
connected as shown in Figure 3. Capacitor values are dependent
on crystal type and should be specified by the crystal manufac-
turer. A parallel-resonant, fundamental frequency, microproces-
sor-grade crystal should be used.
A clock output (CLKOUT) signal is generated by the proces-
sor at the processor’s cycle rate. This can be enabled and
disabled by the CLKODIS bit in the SPORT0 Autobuffer
Control Register.
CLKIN
CLKOUT
XTAL
DSP
Figure 3. External Crystal Connections
Reset
The
RESET
signal initiates a master reset of the ADSP-2184.
The
RESET
signal must be asserted during the power-up
sequence to assure proper initialization.
RESET
during initial
power-up must be held long enough to allow the internal clock
to stabilize. If
RESET
is activated any time after power-up, the
clock continues to run and does not require stabilization time.
The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid V
DD
is
applied to the processor, and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum of
2000 CLKIN cycles ensures that the PLL has locked, but does
not include the crystal oscillator start-up time. During this
power-up sequence the
RESET
signal should be held low. On
any subsequent resets, the
RESET
signal must meet the mini-
mum pulsewidth specification, t
RSP
.
The
RESET
input contains some hysteresis; however, if you use
an RC circuit is used to generate your
RESET
signal, the use of
an external Schmidt trigger is recommended.
The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When
RESET
is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes. In an EZ-ICE-compatible system
RESET
and
ERESET
have the same functionality. For complete informa-
tion, see Designing an EZ-ICE-Compatible Systems section.
MEMORY ARCHITECTURE
The ADSP-2184 provides a variety of memory and peripheral
interface options. The key functional groups are Program Memory,
Data Memory, Byte Memory and I/O.
Program Memory
(Full Memory Mode)
is a 24-bit-wide space
for storing both instruction opcodes and data. The ADSP-2184
has 4K words of Program Memory RAM on chip, and the capabil-
ity of accessing up to two 8K external memory overlay spaces using
the external data bus. Both an instruction opcode and a data value
can be read from on-chip program memory in a single cycle.
Data Memory (Full Memory Mode)
is a 16-bit-wide space
used for the storage of data variables and for memory-mapped
control registers. The ADSP-2184 has 4K words on Data
Memory RAM on chip. Support also exists for up to two 8K
external memory overlay spaces through the external data bus.
Byte Memory
(Full Memory Mode)
provides access to an
8-bit wide memory space through the Byte DMA (BDMA) port.
The Byte Memory interface provides access to 4 MBytes of
memory by utilizing eight data lines as additional address lines.
This gives the BDMA Port an effective 22-bit address range. On
power-up, the DSP can automatically load bootstrap code from
byte memory.
I/O Space
(Full Memory Mode)
allows access to 2048 loca-
tions of 16-bit-wide data. It is intended to be used to communi-
cate with parallel peripheral devices such as data converters and
external registers or latches.
Program Memory
The ADSP-2184 contains 4K
×
24 of on-chip program RAM.
The on-chip program memory is designed to allow up to two
accesses each cycle so that all operations can complete in a
single cycle. In addition, the ADSP-2184 allows the use of 8K
external memory overlays.
The program memory space organization is controlled by the
Mode B pin and the PMOVLAY register. Normally, the ADSP-
2184 is configured with Mode B = 0 and program memory
organized as shown in Figure 4.
EXTERNAL 8K
(PMOVLAY = 1 or 2,
MODE B = 0)
0x3FFF
0x2000
0x1FFF
4K INTERNAL
0x0000
PROGRAM MEMORY
ADDRESS
0x1000
0x0FFF
RESERVED
MEMORY
RANGE
Figure 4. Program Memory (Mode B = 0)
相關PDF資料 |
PDF描述 |
|---|---|
| 218 | Interface IC |
| 21904 | MARKER LABORATORY BLACK |
| 21906 | Low-Frequency, Spread-Spectrum EconOscillator |
| 2191G140IP | Low-Frequency, Spread-Spectrum EconOscillator |
| 2191G-160IP | Low-Frequency, Spread-Spectrum EconOscillator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 218-4"x60yd | 功能描述:膠帶 218 4 X 60 YD BULK RoHS:否 制造商:3M Electronic Specialty 產品:Tapes 類型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 顏色: 材料:Copper Foil 寬度:1 in x 18 yds |
| 218400 | 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:5 x 20 mm Time Lag Fuse (Slo-Blo) Fuse |
| 2-1840026-1 | 制造商:TRP CONNECTOR LTD. 功能描述:MAG45(TM) RJ45/USB 10/100 UR204P12 W LED - Trays 制造商:TRP CONNECTOR B.V. 功能描述:MAG45 RJ45/USB 10/100 UR204P12 |
| 218400P | 制造商:LITTELFUSE 制造商全稱:Littelfuse 功能描述:5 x 20 mm Time Lag Fuse (Slo-Blo) Fuse |
| 218402-000 | 制造商:TE Connectivity 功能描述:CBL 1CNDCTR 16AWG 1.96MM NKL PLTD CPPR RD 600VAC - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:22759/41-16-2 制造商:TE Connectivity 功能描述:High Performance Cable 1Conductors 16AWG 1.96mm Nickel Plated Copper Red 600VAC |
發布緊急采購，3分鐘左右您將得到回復。