- 您現在的位置：買賣IC網 > PDF目錄9990 > XRT75R12DIB (Exar Corporation)IC LIU E3/DS3/STS-1 12CH 420TBGA PDF資料下載
參數資料
| 型號： | XRT75R12DIB |
| 廠商： | Exar Corporation |
| 文件頁數： | 12/133頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| 標準包裝： | 40 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 12/12 |
| 規程： | DS3，E3，STS-1 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 420-LBGA 裸露焊盤 |
| 供應商設備封裝： | 420-TBGA（35x35） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁
XRT75R12D
105
REV. 1.0.3
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
b. The "Transmitting" Network Equipment will notify the remote terminal of this byte-stuffing event, by invert-
ing certain bits within the "pointer word" (within the H1 and H2 bytes) that are referred to as "I" bits.
Figure 52 presents an illustration of the bit-format within the 16-bit word (consist of the H1 and H2 bytes) with
the "I" bits designated.
NOTE: At this time the "I" bits are inverted in order to denote that an "incrementing" pointer adjustment event is currently
occurring.
During the STS-1 frame that follows the "Byte-Stuffing" event
The "I" bits (within the "pointer-word") will be set back to their normal value; and the contents of the H1 and H2
bytes will be incremented by "1".
If f1 > f2
If frequency f1 is greater than f2, then this means that the STS-1 data is being clocked into the "Slip Buffer" at
a faster rate than is being clocked out. In this case, the "Slip Buffer" will start to fill up. Whenever this occurs,
a typical strategy is to delete (e.g., negative-stuff) a byte from the Slip Buffer. The purpose of this "negative-
stuffing" is to compensate for the frequency differences between f1 and f2; and to attempt to keep the "Slip
Buffer" at a somewhat constant fill-level.
NOTE: This byte, which is being "un-stuffed" does carry valuable information for the user (e.g., this byte is typically a
payload byte). Therefore, whenever this negative stuffing occurs, two things must happen.
a. The "negative-stuffed" byte must not be simply discarded. In other words, it must somehow also be
transmitted to the remote PTE with the remainder of the SPE data.
b. The remote PTE must be notified of the occurrence of these "negative-stuffing" events. Further, the
remote PTE must know where to obtain this "negative-stuffed" byte.
Negative-Stuffing and Pointer-Decrementing in a SONET Network
Whenever this "byte negative-stuffing" occurs then the following other things occur within the STS-1 data-
stream.
During the STS-1 frame that contains the "Negative Byte-Stuffing" Event
a. The "Negative-Stuffed" byte will be inserted into the H3 byte position. Whenever an SPE data byte is
inserted into the H3 byte position (which is ordinarily an unused byte), the number of bytes that will exist
between the H3 byte and the J1 byte within the very next SPE will be reduced by 1 byte.
As a
consequence, in this case, the J1 byte (and in-turn, the rest of the SPE) will now be "byte-shifted"
towards the H3 byte position.
FIGURE 52. AN ILLUSTRATION OF THE BIT FORMAT WITHIN THE 16-BIT WORD (CONSISTING OF THE H1 AND H2
BYTES
) WITH THE "I" BITS DESIGNATED
D
I
D
I
D
I
D
I
D
I
S
N
LSB
MSB
H2 Byte
H1 Byte
10 Bit Pointer Expression
相關PDF資料 |
PDF描述 |
|---|---|
| XRT75R12IB | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| ISL267450AIUZ-T | IC INTERFACE |
| MS3116P16-8P | CONN PLUG 8POS STRAIGHT W/PINS |
| IDT72V815L15PFI | IC FIFO SYNC 512X18 15NS 128QFP |
| MS27513E8F35SD | CONN RCPT 6POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT75R12DIB-F | 功能描述:網絡控制器與處理器 IC 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT75R12DIB-L | 功能描述:LIN 收發器 Synch RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| XRT75R12ES | 功能描述:時鐘合成器/抖動清除器 12CH T3/E3/STS1LIUJA 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| XRT75R12IB | 功能描述:外圍驅動器與原件 - PCI 12CH E3/DS3/STS W/JITTER R3 TECH RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| XRT75R12IB-F | 功能描述:外圍驅動器與原件 - PCI 12 Channel 3.3V-5V temp -45 to 85C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。