TABLE
參數資料
型號： XRT75L06IB-F
廠商： Exar Corporation
文件頁數： 50/63頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝： 60
類型： 線路接口裝置（LIU）
驅動器/接收器數： 6/6
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 217-BBGA
供應商設備封裝： 217-BGA（23x23）
包裝： 托盤
XRT75L06
REV. 1.0.3
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
51
TABLE 18: REGISTER MAP DESCRIPTION - CHANNEL N
ADDRESS
(HEX)
TYPE
REGISTER
NAME
BIT#
SYMBOL
DESCRIPTION
DEFAULT
VALUE
0x01 (ch 0)
0x11 (ch 1)
0x21 (ch 2)
0x31 (ch 3)
0x41 (ch 4)
0x51 (ch 5)
R/W
Interrupt
Enable
(source
level)
D0
DMOIE_n
If the Driver Monitor (connected to the output of the
channel) detects the absence of pulses for 128 con-
secutive cycles, it will set the interrupt flag if this bit
has been set.
0
D1
RLOSIE_n This flag will allow a loss of receive signal(for that
channel) to send an interrupt to the Host when this
bit is set.
0
D2
RLOLIE_n
This flag will allow a loss of lock condition to send an
interrupt to the Host when this bit is set.
0
D3
FLIE_n
Set this bit to enable the interrupt when the FIFO
Limit of the Jitter Attenuator is within 2 bits of over-
flow/underflow condition.
NOTE: This bit field is ignored when the Jitter Atten-
uator is disabled.
0
D4
PRBSERIE
_n
Set this bit to enable the interrupt when the PRBS
error is detected.
0
D5
PRBSERC
NTIE_n
Set this bit to enable the interrupt when the PRBS
error count register saturates.
0
D6-D7
Reserved
0x02 (ch 0)
0x12 (ch 1)
0x22 (ch 2)
0x32 (ch 3)
0x42 (ch 4)
0x52 (ch 5)
Reset
on
Read
Interrupt
Status
(source
level)
D0
DMOIS_n
If the Drive monitor circuot detects the absence of
pulses for 128 consecutive cycles, t will set this
interrupt status flag (if enabled) This bit is set on a
change of state of the DMO circuit.
0
D1
RLOSIS_n This flag will indicate a change of “l(fā)oss of Receive
signal” to the Host when this bit is set.
0
D2
RLOLIS_n
This flag will allow a change in the loss of lock condi-
tion to send an interrupt to the Host when this bit is
enabled.Loss of lock is defined as a difference of
greater than 0.5% between the recovered clock and
the channel’s reference clock. Any change (return to
lock) will trigger the interrupt status flag again.
0
D3
FLIS_n
This bit will generate an interrupt if the jitter attenua-
tor FIFO reaches (or leaves) a limit condition. This
limit condition is defined as the FIFO being within
two counts of full or empty.
0
D4
PRBSERIS
_n
This bit is set when the PRBS error occurs.
0
D5
PRBSERC
NTIS_n
This bit is set when the PRBS error count register
saturates.
0
D7-D6
Reserved
相關PDF資料
PDF描述
XRT75R03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R12DIB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
相關代理商/技術參數
參數描述
XRT75R03 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:EXAR DATA SHEET FORMAT TEMPLATES
XRT75R03DES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+D 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIV 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*