ASYNCHRONOUS AN" />
參數資料
型號： XRT75L06IB-F
廠商： Exar Corporation
文件頁數： 42/63頁
文件大?。?/td> 0K
描述： IC LIU E3/DS3/STS-1 6CH 217BGA
標準包裝： 60
類型： 線路接口裝置（LIU）
驅動器/接收器數： 6/6
規程： DS3，E3，STS-1
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 217-BBGA
供應商設備封裝： 217-BGA（23x23）
包裝： 托盤
XRT75L06
SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
REV. 1.0.3
44
6.2
ASYNCHRONOUS AND SYNCHRONOUS DESCRIPTION
Whether the LIU is configured for Asynchronous or Synchronous mode, the following descriptions apply. The
synchronous mode requires an input clock (PCLK) to be used as the microprocessor timing reference. Read
and Write operations are described below.
Read Cycle (For Pmode = "0" or "1")
Whenever the local P wishes to read the contents of a register, it should do the following.
1. Place the address of the target register on the address bus input pins Addr[7:0].
2. While the P is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables communication between the P and
the LIU microprocessor interface block.
3. Next, the P should indicate that this current bus cycle is a Read operation by toggling the RD input pin
"Low". This action enables the bi-directional data bus output drivers of the LIU.
4. After the P toggles the Read signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
to inform the P that the data is available to be read by the P, and that it is ready for the next command.
5. After the P detects the RDY signal and has read the data, it can terminate the Read Cycle by toggling the
RD input pin "High".
6. The CS input pin must be pulled "High" before a new command can be issued.
Write Cycle (For Pmode = "0" or "1")
Whenever a local P wishes to write a byte or word of data into a register within the LIU, it should do the follow-
ing.
1. Place the address of the target register on the address bus input pins Addr[7:0].
2. While the P is placing this address value on the address bus, the address decoding circuitry should
assert the CS pin of the LIU, by toggling it "Low". This action enables communication between the P and
the LIU microprocessor interface block.
3. The P should then place the byte or word that it intends to write into the target register, on the bi-direc-
tional data bus D[7:0].
4. Next, the P should indicate that this current bus cycle is a Write operation by toggling the WR input pin
"Low". This action enables the bi-directional data bus input drivers of the LIU.
5. After the P toggles the Write signal "Low", the LIU will toggle the RDY output pin "Low". The LIU does this
to inform the P that the data has been written into the internal register location, and that it is ready for the
next command.
6. The CS input pin must be pulled "High" before a new command can be issued.
相關PDF資料
PDF描述
XRT75R03DIV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R03IV-F IC LIU E3/DS3/STS-1 3CH 128LQFP
XRT75R06DIB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R06IB-F IC LIU E3/DS3/STS-1 6CH 217BGA
XRT75R12DIB-L IC LIU E3/DS3/STS-1 12CH 420TBGA
相關代理商/技術參數
參數描述
XRT75R03 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH JITTER ATTENUATOR
XRT75R03D 制造商:EXAR 制造商全稱:EXAR 功能描述:THREE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCRONIZER
XRT75R03D_06 制造商:EXAR 制造商全稱:EXAR 功能描述:EXAR DATA SHEET FORMAT TEMPLATES
XRT75R03DES 功能描述:時鐘合成器/抖動清除器 3CH T3/E3/STS1LIU+D 3.3V W/REDUNDANCY RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
XRT75R03DIV 功能描述:時鐘合成器/抖動清除器 3CHNNEL E3/DS3/STS 1 JITTER ATTENUATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*