- 您現在的位置：買賣IC網 > PDF目錄3761 > XR68C92IJTR-F (Exar Corporation)DUAL CHANNEL UART 44PLCC PDF資料下載
參數資料
| 型號： | XR68C92IJTR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 6/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | DUAL CHANNEL UART 44PLCC |
| 標準包裝： | 500 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶自動流量控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC（16.59x16.59） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
XR68C92/192
14
Rev. 1.33
command register) and the CPU cannot stop it. When
the stop command is issued (by reading the stop C/T
command register), the CPU only resets the C/T inter-
rupt. This mode allows the C/T to be used as a
programmable clock source for channels A and B (see
CSRA, CSRB register), and/or a periodic interrupt
generator. In this mode, the C/T generates a square-
wave output (see Figure 2) derived from the pro-
grammed timer input clock source. The square wave
generated by the timer has a period of 2 X (pre-load
value) X (period of clock source) and is available as a
clock source for both channels A and B. Since the timer
cannot be stopped, the values in the registers
(CUR:CLR) should not be read. See description of
ACR register to see how to choose clock source for the
C/T.
When the start counter command register (STCR,
address 0xE) is read, the C/T terminates the current
countdown sequence and sets its output to a '1' (OP3
can be programmed to show this output). The C/T is
then initialized to the pre-load value, and begins a new
countdown sequence. When the terminal count is
reached (0x0000), the C/T sets its output to a '0'. Then,
it gets re-initialized to the pre-load value and repeats
the countdown sequence. See Figure 2 for the result-
ing waveform.
The timer sets the C/T-ready bit in the interrupt status
register (ISR Bit-3) every other time it reaches the
terminal count (at every rising edge of the output).
Users can program the timer to generate an interrupt
request for this condition (every second countdown
cycle) on the -INT output. If the CPU changes the pre-
load value, the timer will not recognize the new value
until either
(a) it reaches the next terminal count and is reinitialized
automatically, or
(b) it is forced to re-initialize by a start command.
When a read at the stop counter command address is
performed, the timer clears ISR Bit-3 but does not stop.
Because in timer mode the C/T runs continuously, it
should be completely configured (pre-load value
loaded and start counter command issued) before
programming the timer output to appear on OP3.
OTHER PROGRAMMING REMARKS
The contents of internal registers should not be
changed during receiver/transmitter operation as cer-
tain changes can produce undesired results. For ex-
ample, changing the number of bits per character while
the transmitter is active will result in transmitting an
incorrect character. The contents of the clock-select
register (CSR) and ACR Bit-7 should only be changed
after the receiver(s) and transmitter(s) have been
issued software RX and TX reset commands. Simi-
larly, changes to the auxiliary control register (ACR Bits
4-6) should only be made while the counter/timer (C/T)
is not used.
The mode registers of each channel MR0, MR1 and
MR2 are accessed via an auxiliary pointer. The pointer
is set to mode register one (MR1) by RESET. It can be
set to MR0 or MR1
by issuing a “reset pointer”
command (0xB0 or 0x10 respectively) via the
channel's command register. Any read or write of the
mode register switches the pointer to next mode reg-
ister. All accesses subsequent to reading/writing MR1
will address MR2 unless the pointer is reset to MR0 or
MR1 as described above. The mode, command,
clock-select, and status registers are duplicated for
each channel to allow independent operation and
control (except that both channels are restricted to
baud rates that are in the same set).
相關PDF資料 |
PDF描述 |
|---|---|
| XR68C192CVTR-F | IC UART FIFI DUAL 44LQFP |
| ST16C650AIQ48-F | IC UART FIFO 32B 48TQFP |
| XR16L2450IM-F | IC UART FIFO 1B DUAL 48TQFP |
| XR68C192CJTR-F | IC UART FIFI DUAL 44PLCC |
| ST16C2450IJ44-F | IC UART FIFO DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR68C92IP | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER |
| XR68C92IV | 制造商:Exar Corporation 功能描述: |
| XR68C92IV-F | 功能描述:UART 接口集成電路 Dual Channel UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR68C92IVTR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 8Byte FIFO 3.3V/5V 44-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR68C92IVTR-F |
| XR68M752 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。