- 您現在的位置：買賣IC網 > PDF目錄16512 > XR19L212IL48-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L202 48QFN PDF資料下載
參數資料
| 型號： | XR19L212IL48-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 49/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR19L202 48QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁
XR19L212
6
TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.1
1.0
PRODUCT DESCRIPTION
The XR19L212 consists of a two-channel UART and RS-232 transceivers. It operates from a single +3V to
5.5V supply with data rates up to 1Mbps, while meeting all EIA RS-232F specifications. Its feature set is fully
compatible to the industry standard 16C550. Unlike the 16C550, most of the modem signals are not CMOS/
TTL level, but conform to EIA/TIA 232 or RS-232 voltage levels. The only two signals that are CMOS/TTL level
are the TXB and RXB signals. They can be used with an external IR or RS-422 transceiver when their
corresponding RS-232 signals, TXDB and RXDB, are not used. The configuration register set is 16550 UART
compatible for control, status and data transfer. Also, the L212 has 64-bytes of transmit and receive FIFOs,
automatic RTS/CTS hardware flow control, automatic Xon/Xoff and special character software flow control,
transmit and receive FIFO trigger levels, and a programmable fractional baud rate generator with a prescaler
of divide by 1 or 4. Additionally, the L212 includes the ACP pin which the user can shut down the charge pump
for the RS-232 drivers. In the UART portion, the Power-Save feature isolates the databus interface to further
reduce power consumption in the Sleep mode. The L212 is fabricated using an advanced CMOS process.
Enhanced Features
The L212 UART provides a solution that supports 64 bytes of transmit and receive FIFO. Increased
performance is realized in the L212 by the transmit and receive FIFOs, FIFO trigger level controls and
automatic flow control mechanism. This allows the external processor to handle more networking tasks within
a given time. This increases the service interval giving the external CPU additional time for other applications
and reducing the overall UART interrupt servicing time. In addition, the L212 provides the ACP and Power-
Save modes that drastically reduces the power consumption when the device is not used. The combination of
the above greatly reduces the CPU’s bandwidth requirement, increases performance, and reduces power
consumption.
Intel or Motorola Data Bus Interface
The L212 provides a host interface that supports Intel or Motorola microprocessor (CPU) data bus interface.
The Intel bus compatible interface allows direct interconnect to Intel compatible type of CPUs using IOR#,
IOW# and CS# inputs for data bus operation. The Motorola bus compatible interface instead uses the R/W#
and CS# signals for data bus transactions. See pin description section for details on all the control signals. The
Intel and Motorola bus interface selection is made through the pin, I/M#.
Data Rate
The L212 is capable of operation up to 1 Mbps data rate. The UART section can operate at much higher
speeds, but the speed of the RS-232 transceiver is limited to 1 Mbps. The device can operate either with a
crystal on pins XTAL1 and XTAL2, or external clock source on XTAL1 pin.
Internal Enhanced Register Sets
The L212 UART has a set of enhanced registers providing control and monitoring functions. Interrupt enable/
disable and status, FIFO enable/disable, selectable TX and RX FIFO trigger levels, automatic hardware/
software flow control enable/disable, programmable baud rates, modem interface controls and status, sleep
mode and infrared mode are all standard features. Following a power on reset or an external reset (and
operating in 16 or Intel Mode), the registers defaults to the reset condition and is compatible with the 16C550.
RS-232 Interface
The L212 includes RS-232 drivers/receivers for the modem interface. This feature eliminates the need for an
external RS-232 transceiver. The charge pump provides output voltages of +5V and -5V for its drivers over the
3.3V to 5.5V VCC supply voltage. The serial outputs TXD and RTS swing between -5V (inactive) and 5V
(active) RS-232 voltage levels. The serial inputs RXD and CTS are RS-232 receivers and can take any voltage
swing from -15V to +15V. The receivers are always active, even in Full Sleep and Power-Save modes. The
RS-232 drivers guarantee a data rate of 1 Mbps even when fully loaded with 3Kohm in parallel with 1000pF
load.
All RS-232 drivers and receivers are protected to ±15kV using the Human Body Model ground combination,
±8kV using IEC 61000-4-2 Contact Discharge, and ±15kV using IEC 61000-4-2 Air-Gap Discharge. For more
information, send an e-mail to uarttechsupport@exar.com.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-25M-EX | CONVERTER MOD DC/DC 10V 75W |
| A3BKB-1018G | IDC CABLE- ASR10B/AE10G/APK10B |
| VI-JVT-EZ-S | CONVERTER MOD DC/DC 6.5V 25W |
| UPJ1K470MPD6TD | CAP ALUM 47UF 80V 20% RADIAL |
| H3WWH-2406G | IDC CABLE - HPL24H/AE24G/HPL24H |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L212IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L212IL48TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 64Byte FIFO 5V 48-Pin QFN EP T/R 制造商:Exar Corporation 功能描述:XR19L212IL48TR-F |
| XR19L220 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L220_07 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L220IL40 | 制造商:EXAR 制造商全稱:EXAR 功能描述:SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
發布緊急采購，3分鐘左右您將得到回復。