- 您現在的位置：買賣IC網 > PDF目錄16512 > XR19L210IL40-0B-EB (Exar Corporation)EVAL BOARD FOR XR19L202 40QFN PDF資料下載
參數資料
| 型號： | XR19L210IL40-0B-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 19/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR19L202 40QFN |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
XR19L210
26
SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER
REV. 1.0.2
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced LOW).
This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition (default).
Logic 1 = Forces the transmitter output (TX) LOW for alerting the remote receiver of a line break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM) enable.
Logic 0 = Data registers are selected (default).
Logic 1 = Divisor latch registers are selected.
4.8
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# output is not available as an output on this device. But for 16C550 compatibility, it can still be used
in internal loopback mode.
Logic 0 = Force DTR output HIGH (default).
Logic 1 = Force DTR output LOW.
MCR[1]: RTS Output
The RTS pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS output HIGH (default).
Logic 1 = Force RTS output LOW.
MCR[2]: OP1# (legacy term)
The OP1# output is not available on the XR19L210, however, it is available in internal loopback. In the Internal
Loopback Mode, this bit controls the state of the modem input RI bit in the MSR register as shown in
Logic 0 = OP1# is HIGH (default).
Logic 1 = OP1# is LOW.
In the Internal Loopback Mode, this bit controls the state of the modem input RI bit in the MSR register as
shown in Figure 11.
MCR[3]: INT Output Enable or OP2# (legacy term)
This bit enables and disables the operation of interrupt output, INT in the Intel mode. If INT output is not used,
OP2# can be used as a general purpose output in the Intel mode. In the Motorola mode, this bit must be set to
logic 0.
Logic 0 = INT output disabled (three state mode) in Intel mode (default).
Logic 1 = INT output enabled (active mode) in Intel mode.
In the Internal Loopback Mode, this bit functions like the OP2# in the 16C550 and is used to set the state of the
modem input CD bit in the MSR register.
MCR[4]: Internal Loopback Enable
Logic 0 = Disable loopback mode (default).
Logic 1 = Enable local loopback mode, see loopback section and Figure 11.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-252-EX | CONVERTER MOD DC/DC 15V 75W |
| 5504972-4 | CABLE ASSEM FIBER SC-ST 5 METER |
| ILSB1206ER6R8K | INDUCTOR 6.8UH 10% 1206 |
| EBC31DRTS-S13 | CONN EDGECARD 62POS .100 EXTEND |
| ILSB1206ER68NM | INDUCTOR 0.068UH 20% 1206 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR19L210IL40-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR19L212 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:TWO CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER |
| XR19L212IL48-0B-EB | 功能描述:界面開發工具 Supports L212 48 pin QFN, PCI Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR19L212IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。