- 您現在的位置：買賣IC網 > PDF目錄11815 > XR17V258IV (Exar Corporation)IC UART PCI BUS OCTAL 144LQFP PDF資料下載
參數資料
| 型號： | XR17V258IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 48/69頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART PCI BUS OCTAL 144LQFP |
| 產品變化通告： | Leaded UART, V&I Obsolescence 11/Apr/2011 |
| 標準包裝： | 60 |
| 特點： | * |
| 通道數： | 8 |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
XR17V258
52
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.2
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
5.10
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general
purpose inputs/outputs when they are not used with modem signals.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit [3] in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
MSR[6]: RI Input Status
Normally this bit is the complement of the RI# input. In the loopback mode this bit is equivalent to bit [2] in the
MCR register. The RI# input may be used as a general purpose input when the modem interface is not used.
MSR[5]: DSR Input Status
DSR# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=1). Auto CTS/DSR flow control
allows starting and stopping of local data transmissions based on the modem DSR# signal. A HIGH on the
DSR# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW
will resume data transmission. Normally MSR bit [5] is the complement of the DSR# input. However in the
loopback mode, this bit is equivalent to the DTR# bit in the MCR register. The DSR# input may be used as a
general purpose input when the modem interface is not used.
MSR[4]: CTS Input Status
CTS# pin may function as automatic hardware flow control signal input if it is enabled and selected by Auto
CTS/DSR bit (EFR bit [6]=1) and RTS/DTR flow control select bit (MCR bit [2]=0). Auto CTS/DSR flow control
allows starting and stopping of local data transmissions based on the modem CTS# signal. A HIGH on the
CTS# pin will stop UART transmitter as soon as the current character has finished transmission, and a LOW
will resume data transmission. Normally MSR bit [4] is the complement of the CTS# input. However in the
loopback mode, this bit is equivalent to the RTS# bit in the MCR register. The CTS# input may be used as a
general purpose input when the modem interface is not used.
MSR[3]: Delta CD# Input Flag
Logic 0 = No change on CD# input (default).
Logic 1 = Indicates that the CD# input has changed state since the last time it was monitored. A modem
status interrupt will be generated if MSR interrupt is enabled (IER bit [3]).
MSR[2]: Delta RI# Input Flag
Logic 0 = No change on RI# input (default).
Logic 1 = The RI# input has changed from a LOW to a HIGH, ending of the ringing signal. A modem status
interrupt will be generated if MSR interrupt is enabled (IER bit [3]).
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B7H-IX-F2 | CONVERTER MOD DC/DC 52V 75W |
| ATMEGA324P-B15AZ | IC MCU 8BIT 32KB FLASH 44TQFP |
| MS3110F14-19S | CONN RCPT 19POS WALL MNT W/SCKT |
| VI-B7H-IX-F1 | CONVERTER MOD DC/DC 52V 75W |
| MS3116F14-19SY | CONN PLUG 19POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V258IV-0A-EVB | 功能描述:UART 接口集成電路 Supports V258 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V258IVF | 制造商:Exar Corporation 功能描述: |
| XR17V258IV-F | 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V258IVTR-F | 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V352 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUAL PCI EXPRESS UART |
發布緊急采購，3分鐘左右您將得到回復。