- 您現在的位置：買賣IC網 > PDF目錄11815 > XR17V258IV (Exar Corporation)IC UART PCI BUS OCTAL 144LQFP PDF資料下載
參數資料
| 型號： | XR17V258IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 40/69頁 |
| 文件大小： | 0K |
| 描述： | IC UART PCI BUS OCTAL 144LQFP |
| 產品變化通告： | Leaded UART, V&I Obsolescence 11/Apr/2011 |
| 標準包裝： | 60 |
| 特點： | * |
| 通道數： | 8 |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
XR17V258
45
REV. 1.0.2
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
IER[4]: Reserved
IER[3]: Modem Status Interrupt Enable
The Modem Status Register interrupt is issued whenever any of the delta bits of the MSR register (bits [3:0]) is
set.
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
IER[2]: Receive Line Status Interrupt Enable
An Overrun error, Framing error, Parity error or detection of a Break character will result in an LSR interrupt.
The V258 will issue an LSR interrupt immediately after receiving a character with an error. It will again re-issue
the interrupt (if the first one has been cleared by reading the LSR register) when the character with the error is
on the top of the FIFO, meaning the next one to be read out of the FIFO.
For example, let’s consider an incoming data stream of 0x55, 0xAA, etc. and that the character 0xAA has a
Parity error associated with it. Let’s assume that the character 0x55 has not been read out of the FIFO yet. The
V258v258 will issue an interrupt as soon as the stop bit of the character 0xAA is received. The LSR register will
have only the FIFO error bit (bit [7]) set and none of the other error bits (bits [4:1]) will be set, since the byte on
the top of the FIFO is 0x55 which does not have any errors associated with it. When this byte has been read
out, the V258 will issue another LSR interrupt and this time the LSR register will show the Parity bit (bit [2]) set.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[1]: TX Ready Interrupt Enable
In non-FIFO mode, a TX interrupt is issued whenever the THR is empty. In the FIFO mode, an interrupt is
issued twice: once when the number of bytes in the TX FIFO falls below the programmed trigger level and
again when the TX FIFO becomes empty. When autoRS485 mode is enabled (FCTR bit [5] = 1), the second
interrupt is delayed until the transmitter (both the TX FIFO and the TX Shift Register) is empty.
Logic 0= Disable Transmit Ready Interrupt (default).
Logic 1 = Enable Transmit Ready Interrupt.
IER[0]: RX Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
5.5
Interrupt Status Register (ISR) - Read Only
The UART provides multiple levels of prioritized interrupts to minimize external software interaction. The
Interrupt Status Register (ISR) provides the user with six interrupt status bits. Performing a read cycle on the
ISR will give the user the current highest pending interrupt level to be serviced, others queue up for next
service. No other interrupts are acknowledged until the pending interrupt is serviced. The Interrupt Source
Table, Table 16, shows the data values (bit [5:0]) for the six prioritized interrupt levels and the interrupt sources
associated with each of these interrupt levels.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B7H-IX-F2 | CONVERTER MOD DC/DC 52V 75W |
| ATMEGA324P-B15AZ | IC MCU 8BIT 32KB FLASH 44TQFP |
| MS3110F14-19S | CONN RCPT 19POS WALL MNT W/SCKT |
| VI-B7H-IX-F1 | CONVERTER MOD DC/DC 52V 75W |
| MS3116F14-19SY | CONN PLUG 19POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V258IV-0A-EVB | 功能描述:UART 接口集成電路 Supports V258 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V258IVF | 制造商:Exar Corporation 功能描述: |
| XR17V258IV-F | 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V258IVTR-F | 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V352 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUAL PCI EXPRESS UART |
發布緊急采購，3分鐘左右您將得到回復。