- 您現在的位置：買賣IC網 > PDF目錄11815 > XR17V258IV (Exar Corporation)IC UART PCI BUS OCTAL 144LQFP PDF資料下載
參數資料
| 型號： | XR17V258IV |
| 廠商： | Exar Corporation |
| 文件頁數： | 39/69頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART PCI BUS OCTAL 144LQFP |
| 產品變化通告： | Leaded UART, V&I Obsolescence 11/Apr/2011 |
| 標準包裝： | 60 |
| 特點： | * |
| 通道數： | 8 |
| FIFO's： | 64 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 144-LQFP |
| 供應商設備封裝： | 144-LQFP（20x20） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
XR17V258
44
66MHZ PCI BUS OCTAL UART WITH POWER MANAGEMENT SUPPORT
REV. 1.0.2
5.0 UART CONFIGURATION REGISTERS
5.1
Receive Holding Register (RHR) - Read only
5.2
Transmit Holding Register (THR) - Write only
5.3
Baud Rate Generator Divisors (DLM, DLL and DLD)
The Baud Rate Generator (BRG) generates the data rate for the transmitter and receiver. The rate is
programmed through registers DLM, DLL and DLD which are only accessible when LCR bit [7] is set to logic 1.
Refer to “Section 4.1, Programmable Baud Rate Generator with Fractional Divisor” on page 31 for more
details.
5.4
Interrupt Enable Register (IER) - Read/Write
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR) and also
encoded in INT (INT0-INT3) register in the Device Configuration Registers.
5.4.1
IER versus Receive FIFO Interrupt Mode Operation
When the receive FIFO (FCR bit [0] = logic 1) and receive interrupts (IER bit [0] = logic 1) are enabled, the
RHR interrupts (see ISR bits [4:3]) status will reflect the following:
A.
The receive data available interrupts are issued to the host when the FIFO has reached the programmed
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
B.
FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
C.
The receive data ready bit (LSR bit [0]) is set as soon as a character is transferred from the shift register to
the receive FIFO. It is reset when the FIFO is empty.
IER versus Receive/Transmit FIFO Polled Mode Operation
When FCR bit [0] equals a logic 1 for FIFO enable; resetting IER bits [3:0] enables the XR16V258 in the FIFO
polled mode of operation. Since the receiver and transmitter have separate bits in the LSR either can be used
in the polled mode by selecting respective transmit or receive control bit(s).
A.
LSR BIT-0 indicates there is data in RHR (non-FIFO mode) or RX FIFO (FIFO mode).
B.
LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C.
LSR BIT 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D.
LSR BIT-5 indicates THR (non-FIFO mode) or TX FIFO (FIFO mode) is empty.
E.
LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F.
LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[7]: CTS# Input Interrupt Enable (requires EFR bit [4]=1)
Logic 0 = Disable the CTS# interrupt (default).
Logic 1 = Enable the CTS# interrupt. The UART issues an interrupt when CTS# pin makes a transition from
LOW to HIGH.
IER[6]: RTS# Output Interrupt Enable (requires EFR bit [4]=1)
Logic 0 = Disable the RTS# interrupt (default).
Logic 1 = Enable the RTS# interrupt. The UART issues an interrupt when RTS# pin makes a transition from
LOW to HIGH.
IER[5]: Xoff Interrupt Enable (requires EFR bit [4]=1)
Logic 0 = Disable the software flow control, receive Xoff interrupt (default).
Logic 1 = Enable the software flow control, receive Xoff interrupt. See Software Flow Control section for
details.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B7H-IX-F2 | CONVERTER MOD DC/DC 52V 75W |
| ATMEGA324P-B15AZ | IC MCU 8BIT 32KB FLASH 44TQFP |
| MS3110F14-19S | CONN RCPT 19POS WALL MNT W/SCKT |
| VI-B7H-IX-F1 | CONVERTER MOD DC/DC 52V 75W |
| MS3116F14-19SY | CONN PLUG 19POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V258IV-0A-EVB | 功能描述:UART 接口集成電路 Supports V258 144 ld TQFP, PCI Interface RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V258IVF | 制造商:Exar Corporation 功能描述: |
| XR17V258IV-F | 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V258IVTR-F | 功能描述:UART 接口集成電路 66MHz Octal PCI UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR17V352 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUAL PCI EXPRESS UART |
發布緊急采購，3分鐘左右您將得到回復。