REV. 1.0.4 INTSEL 38 - 65 6 I Interrupt Select (active high, input with internal pull" />
參數資料
型號: XR16V564IV80-0A-EB
廠商: Exar Corporation
文件頁數: 51/54頁
文件大小: 0K
描述: EVAL BOARD FOR XR16V564 80LQFP
標準包裝: 1
系列: *
XR16V564/564D
6
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.4
INTSEL
38
-
65
6
I
Interrupt Select (active high, input with internal pull-
down).
When 16/68# pin is HIGH for Intel bus interface, this
pin can be used in conjunction with MCR bit-3 to
enable or disable the INT A-D pins or override MCR
bit-3 and enable the interrupt outputs. Interrupt out-
puts are enabled continuously when this pin is HIGH.
MCR bit-3 enables and disables the interrupt output
pins. In this mode, MCR bit-3 is set to a logic 1 to
enable the continuous output. See MCR bit-3 descrip-
tion for full detail. This pin must be LOW in the Motor-
ola bus interface mode. For the 64 pin packages, this
pin is bonded to VCC internally in the XR16V564D so
the INT outputs operate in the continuous interrupt
mode. This pin is bonded to GND internally in the
XR16V564 and therefore requires setting MCR bit-3
for enabling the interrupt output pins.
MODEM OR SERIAL I/O INTERFACE
TXA
TXB
TXC
TXD
6
8
28
30
8
10
39
41
17
19
51
53
29
32
69
72
O
UART channels A-D Transmit Data and infrared trans-
mit data. Standard transmit and receive interface is
enabled when MCR[6] = 0. In this mode, the TX signal
will be a HIGH during reset, or idle (no data). Infrared
IrDA transmit and receive interface is enabled when
MCR[6] = 1. In the Infrared mode, the inactive state
(no data) for the Infrared encoder/decoder interface is
a logic 0.
RXA
RXB
RXC
RXD
48
13
22
36
62
20
29
51
7
29
41
63
17
44
57
4
I
UART channel A-D Receive Data or infrared receive
data. Normal receive data input must idle HIGH.
RTSA#
RTSB#
RTSC#
RTSD#
3
11
25
33
5
13
36
44
14
22
48
56
26
35
66
75
O
UART channels A-D Request-to-Send (active low) or
general purpose output. This output must be asserted
prior to using auto RTS flow control, see EFR[6],
MCR[1], and IER[6]. Also see
Figure 11. If these
outputs are not used, leave them unconnected.
CTSA#
CTSB#
CTSC#
CTSD#
1
12
23
35
2
16
33
47
11
25
45
59
23
38
63
78
I
UART channels A-D Clear-to-Send (active low) or gen-
eral purpose input. It can be used for auto CTS flow
control, see EFR[7], and IER[7]. Also see
These inputs should be connected to VCC when not
used.
DTRA#
DTRB#
DTRC#
DTRD#
-
3
15
34
46
12
24
46
58
24
37
64
77
O
UART channels A-D Data-Terminal-Ready (active low)
or general purpose output. If these outputs are not
used, leave them unconnected.
DSRA#
DSRB#
DSRC#
DSRD#
-
1
17
32
48
10
26
44
60
22
39
62
79
I
UART channels A-D Data-Set-Ready (active low) or
general purpose input. This input should be connected
to VCC when not used. This input has no effect on the
UART.
Pin Description
NAME
48-QFN
PIN #
64-LQFP
PIN #
68-PLCC
PIN #
80-LQFP
PIN #
TYPE
DESCRIPTION
相關PDF資料
PDF描述
ECM18DRXH CONN EDGECARD 36POS DIP .156 SLD
A3932SEQ IC CTRLR MOSFET 3PH 32-PLCC
RPP30-4824SW CONV DC/DC 30W 18-75VIN 24VOUT
6374645-4 C/A MTRJ TO LC SM OFNR 4M1
XC61CN1802MR-G IC SUPERVISOR 1.8V SOT23-3
相關代理商/技術參數
參數描述
XR16V564IV80-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564IV80TR-F 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 80-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564IV80TR-F
XR16V564IV-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16V564IVTR-F 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564IVTR-F
XR16V598 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO