- 您現在的位置：買賣IC網 > PDF目錄16491 > XR16V564IV80-0A-EB (Exar Corporation)EVAL BOARD FOR XR16V564 80LQFP PDF資料下載
參數資料
| 型號： | XR16V564IV80-0A-EB |
| 廠商： | Exar Corporation |
| 文件頁數： | 28/54頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR XR16V564 80LQFP |
| 標準包裝： | 1 |
| 系列： | * |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
XR16V564/564D
34
2.25V TO 3.6V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.4
4.8
Line Status Register (LSR) - Read/Write
This register is writeable but it is not recommended. The LSR provides the status of data transfers between the
UART and the host. If IER bit-2 is enabled, LSR bit 1 will generate an interrupt immediately and LSR bits 2-4
will generate an interrupt when a character with an error is in the RHR.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[2]: Receive Data Parity Error Tag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR does not have correct parity information and is suspect.
This error is associated with the character available for reading in RHR.
LSR[3]: Receive Data Framing Error Tag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[4]: Receive Break Tag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was LOW for at least one character frame time). In the
FIFO mode, only one break character is loaded into the FIFO. The break indication remains until the RX
input returns to the idle condition, “mark” or HIGH.
LSR[5]: Transmit Holding Register Empty Flag
This bit is the Transmit Holding Register Empty indicator. The THR bit is set to HIGH when the last data byte is
transferred from the transmit holding register to the transmit shift register. The bit is reset to logic 0 concurrently
with the data loading to the transmit holding register by the host. In the FIFO mode this bit is set when the
transmit FIFO is empty, it is cleared when the transmit FIFO contains at least 1 byte.
LSR[6]: THR and TSR Empty Flag
This bit is set to HIGH whenever the transmitter goes idle. It is set to LOW whenever either the THR or TSR
contains a data character. In the FIFO mode this bit is set to HIGH whenever the transmit FIFO and transmit
shift register are both empty.
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = A global indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error
or break indication is in the FIFO data. This bit clears when there is no more error(s) in any of the bytes in the
RX FIFO.
相關PDF資料 |
PDF描述 |
|---|---|
| ECM18DRXH | CONN EDGECARD 36POS DIP .156 SLD |
| A3932SEQ | IC CTRLR MOSFET 3PH 32-PLCC |
| RPP30-4824SW | CONV DC/DC 30W 18-75VIN 24VOUT |
| 6374645-4 | C/A MTRJ TO LC SM OFNR 4M1 |
| XC61CN1802MR-G | IC SUPERVISOR 1.8V SOT23-3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16V564IV80-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V564IV80TR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 80-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564IV80TR-F |
| XR16V564IV-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16V564IVTR-F | 制造商:Exar Corporation 功能描述:UART 4-CH 32Byte FIFO 2.5V/3.3V 64-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR16V564IVTR-F |
| XR16V598 | 制造商:EXAR 制造商全稱:EXAR 功能描述:2.25V TO 3.6V HIGH PERFORMANCE OCTAL UART WITH 16-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。