參數資料
型號： XR16M564IJ68-F
廠商： Exar Corporation
文件頁數： 26/55頁
文件大小： 0K
描述： IC UART FIFO 32B QUAD 68PLCC
標準包裝： 19
特點： *
通道數： 4，QUART
FIFO's： 32 字節
規程： RS232
電源電壓： 1.62 V ~ 3.63 V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 68-LCC（J 形引線）
供應商設備封裝： 68-PLCC
包裝： 管件
XR16M564/564D
32
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.0
LCR[5]: TX and RX Parity Select
If the parity bit is enabled, LCR BIT-5 selects the forced parity format.
LCR BIT-5 = LOW, parity is not forced (default).
LCR BIT-5 = HIGH and LCR BIT-4 = LOW, parity bit is forced to a logical 1 for the transmit and receive data.
LCR BIT-5 = HIGH and LCR BIT-4 = LOW, parity bit is forced to a logical 0 for the transmit and receive data.
LCR[6]: Transmit Break Enable
When enabled, the Break control bit causes a break condition to be transmitted (the TX output is forced to a
“space’, LOW, state). This condition remains, until disabled by setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (default)
Logic 1 = Forces the transmitter output (TX) to a “space”, LOW, for alerting the remote receiver of a line
break condition.
LCR[7]: Baud Rate Divisors Enable
Baud rate generator divisor (DLL/DLM/DLD) enable.
Logic 0 = Data registers are selected. (default)
Logic 1 = Divisor latch registers are selected.
4.7
Modem Control Register (MCR) or General Purpose Outputs Control - Read/Write
The MCR register is used for controlling the serial/modem interface signals or general purpose inputs/outputs.
MCR[0]: DTR# Output
The DTR# pin is a modem control output. If the modem interface is not used, this output may be used as a
general purpose output.
Logic 0 = Force DTR# output HIGH (default).
Logic 1 = Force DTR# output LOW.
MCR[1]: RTS# Output
The RTS# pin is a modem control output and may be used for automatic hardware flow control by enabled by
EFR bit-6. If the modem interface is not used, this output may be used as a general purpose output.
Logic 0 = Force RTS# output HIGH (default).
Logic 1 = Force RTS# output LOW.
MCR[2]: Reserved
OP1# is not available as an output pin on the M564. But it is available for use during Internal Loopback Mode.
In the Loopback Mode, this bit is used to write the state of the modem RI# interface signal.
TABLE 13: PARITY SELECTION
LCR BIT-5 LCR BIT-4 LCR BIT-3
PARITY SELECTION
X
0
No parity
0
1
Odd parity
0
1
Even parity
1
0
1
Force parity to mark, HIGH
1
Forced parity to space, LOW
相關PDF資料
PDF描述
XR16M570IL32-F IC UART FIFO 16B 32QFN
XR16M580IM48-F IC UART FIFO 16B 48TQFP
XR16M581IL32-F IC UART FIFO 16B 32QFN
XR16M598IQ100-F IC UART FIFO 16B OCTAL 100QFP
XR16M654IQ100-F IC UART FIFO 64B QUAD 100QFP
相關代理商/技術參數
參數描述
XR16M564IL-0A-EVB 功能描述:界面開發工具 Eval Board for XR16M564IL-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M564IL-0B-EVB 功能描述:界面開發工具 Eval Board for XR16M564IL-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
XR16M564IL48 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
XR16M564IL48-F 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
XR16M564IV-0A-EVB 功能描述:界面開發工具 Eval Board for XR16M564IV-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*