- 您現在的位置：買賣IC網 > PDF目錄1975 > XR16M564IJ68-F (Exar Corporation)IC UART FIFO 32B QUAD 68PLCC PDF資料下載
參數資料
| 型號： | XR16M564IJ68-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 15/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 32B QUAD 68PLCC |
| 標準包裝： | 19 |
| 特點： | * |
| 通道數： | 4，QUART |
| FIFO's： | 32 字節 |
| 規程： | RS232 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-LCC（J 形引線） |
| 供應商設備封裝： | 68-PLCC |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
XR16M564/564D
22
1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO
REV. 1.0.0
2.17
Sleep Mode with Auto Wake-Up
The M564 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the M564 to enter sleep mode:
■ no interrupts pending for all four channels of the M564 (ISR bit-0 = 1)
■ sleep mode of all channels are enabled (IER bit-4 = 1)
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pins are idling HIGH
The M564 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M564 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M564 is awakened by any one of the above conditions, it will return to the sleep mode automatically after
all interrupting conditions have been serviced and cleared. If the M564 is awakened by the modem inputs, a
read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be entered while
an interrupt is pending from any channel. The M564 will stay in the sleep mode of operation until it is disabled
by setting IER bit-4 to a logic 0.
If the address lines, data bus lines, IOW#, IOR#, CSA#, CSB#, CSC#, CSD# and modem input lines remain
steady when the M564 is in sleep mode, the maximum current will be in the microamp range as specified in the
DC Electrical Characteristics on page 40. If the input lines are floating or are toggling while the M564 is in
sleep mode, the current can be up to 100 times more. If any of those signals are toggling or floating, then an
external buffer would be required to keep the address, data and control lines steady to achieve the low current.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. Also, make sure the RX A-D pins are idling HIGH or “marking”
condition during sleep mode. This may not occur when the external interface transceivers (RS-232, RS-485 or
another type) are also put to sleep mode and cannot maintain the “marking” condition. To avoid this, the
system design engineer can use a 47k ohm pull-up resistor on each of the RX A-D inputs.
2.18
Internal Loopback
The M564 UART provides an internal loopback capability for system diagnostic purposes. The internal
loopback mode is enabled by setting MCR register bit-4 to logic 1. All regular UART functions operate normally.
Figure 13 shows how the modem port signals are re-configured. Transmit data from the transmit shift register
output is internally routed to the receive shift register input allowing the system to receive the same data that it
was sending. The TX pin is held HIGH or mark condition while RTS# and DTR# are de-asserted, and CTS#,
DSR# CD# and RI# inputs are ignored. Caution: the RX input must be held HIGH during loopback test else
upon exiting the loopback test the UART may detect and report a false “break” signal.
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M570IL32-F | IC UART FIFO 16B 32QFN |
| XR16M580IM48-F | IC UART FIFO 16B 48TQFP |
| XR16M581IL32-F | IC UART FIFO 16B 32QFN |
| XR16M598IQ100-F | IC UART FIFO 16B OCTAL 100QFP |
| XR16M654IQ100-F | IC UART FIFO 64B QUAD 100QFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M564IL-0A-EVB | 功能描述:界面開發工具 Eval Board for XR16M564IL-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M564IL-0B-EVB | 功能描述:界面開發工具 Eval Board for XR16M564IL-0B RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M564IL48 | 制造商:EXAR 制造商全稱:EXAR 功能描述:1.62V TO 3.63V QUAD UART WITH 32-BYTE FIFO |
| XR16M564IL48-F | 功能描述:UART 接口集成電路 UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| XR16M564IV-0A-EVB | 功能描述:界面開發工具 Eval Board for XR16M564IV-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。