- 您現在的位置：買賣IC網 > PDF目錄1975 > XR16M2651IM48-F (Exar Corporation)IC UART FIFO 32B DUAL 48TQFP PDF資料下載
參數資料
| 型號： | XR16M2651IM48-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 34/51頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 32B DUAL 48TQFP |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 32 字節 |
| 規程： | RS232，RS422 |
| 電源電壓： | 1.62 V ~ 3.63 V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
XR16M2651
4
HIGH PERFORMANCE DUART WITH 32-BYTE FIFO AND POWERSAVE FEATURE
REV. 1.0.2
INTB
21
29
O
UART channel B Interrupt output. The output state is defined by the user through
the software setting of MCR[3]. INTB is set to the active mode and OP2B# output
LOW when MCR[3] is set to a logic 1. INTB is set to the three state mode and
OP2B# output HIGH when MCR[3] is set to a logic 0 (default). See MCR[3].
TXRDYA#
-
43
O
UART channel A Transmitter Ready (active low). The output provides the TX FIFO/
THR status for transmit channel A. See Table 3. If it is not used, leave it uncon-
nected.
RXRDYA#
-
31
O
UART channel A Receiver Ready (active low). This output provides the RX FIFO/
RHR status for receive channel A. See Table 3. If it is not used, leave it uncon-
nected.
TXRDYB#
-
6
O
UART channel B Transmitter Ready (active low). The output provides the TX FIFO/
THR status for transmit channel B. See Table 4. If it is not used, leave it uncon-
nected.
RXRDYB#
-
18
O
UART channel B Receiver Ready (active low). This output provides the RX FIFO/
RHR status for receive channel B. See Table 3. If it is not used, leave it uncon-
nected.
MODEM OR SERIAL I/O INTERFACE
TXA
5
7
O
UART channel A Transmit Data or infrared encoder data. Standard transmit and
receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be
HIGH during reset or idle (no data). Infrared IrDA transmit and receive interface is
enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the
Infrared encoder/decoder interface is LOW. If it is not used, leave it unconnected.
RXA
4
5
I
UART channel A Receive Data or infrared receive data. Normal receive data input
must idle HIGH. The infrared receiver pulses typically idles at LOW but can be
inverted by software control prior going into the decoder, see MCR[6]. If this pin is
not used, tie it to VCC or pull it high via a 100k ohm resistor.
RTSA#
23
33
O
UART channel A Request-to-Send (active low) or general purpose output. This out-
put must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1],
and IER[6].
CTSA#
25
38
I
UART channel A Clear-to-Send (active low) or general purpose input. It can be
used for auto CTS flow control, see EFR[7], and IER[7]. This input should be con-
nected to VCC when not used.
DTRA#
-
34
O
UART channel A Data-Terminal-Ready (active low) or general purpose output. If it
is not used, leave it unconnected.
DSRA#
-
39
I
UART channel A Data-Set-Ready (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
CDA#
-
40
I
UART channel A Carrier-Detect (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
RIA#
-
41
I
UART channel A Ring-Indicator (active low) or general purpose input. This input
should be connected to VCC when not used. This input has no effect on the UART.
Pin Description
NAME
32-QFN
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
相關PDF資料 |
PDF描述 |
|---|---|
| XR16M2750IM48-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16M2751IM48-F | IC UART FIFO 64B DUAL 48TQFP |
| XR16M2752IJ44-F | IC UART FIFO 64B DUAL 44PLCC |
| XR16M554IV64-F | IC UART FIFO 16B QUAD 64LQFP |
| XR16M564IJ68-F | IC UART FIFO 32B QUAD 68PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR16M2651IM48TR-F | 制造商:Exar Corporation 功能描述:UART 2-CH 32Byte FIFO 1.8V/2.5V/3.3V 48-Pin TQFP T/R 制造商:Exar Corporation 功能描述:XR16M2651IM48TR-F |
| XR16M2750 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M2750IL-0A-EB | 功能描述:界面開發工具 Eval Board for XR16M2750IL-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M2750IL-0B-EB | 功能描述:界面開發工具 Eval Board for XR16M2750IL Series RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR16M2750IL32 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
發布緊急采購，3分鐘左右您將得到回復。