參數資料
型號： XC5202-5PQ100C
廠商： Xilinx Inc
文件頁數： 25/73頁
文件大小： 0K
描述： IC - FPGA SPEED GRADE 5 COM TEMP
產品變化通告： XC1700 PROMs,XC5200,HQ,SCD Parts Discontinuation 19/Jul/2010
標準包裝： 66
系列： XC5200
LAB/CLB數： 64
邏輯元件/單元數： 256
輸入/輸出數： 81
門數： 3000
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 100-BQFP
供應商設備封裝： 100-QFP（14x20）
其它名稱： Q858790
XC5202-5PQ1000C
XC5202-5PQ1000C-ND
R
November 5, 1998 (Version 5.2)
7-113
XC5200 Series Field Programmable Gate Arrays
7
Note that in XC5200-Series devices, configuration data is
not inverted with respect to configuration as it is in XC2000
and XC3000 families.
Readback of Express mode bitstreams results in data that
does not resemble the original bitstream, because the bit-
stream format differs from other modes.
XC5200-Series Readback does not use any dedicated
pins,
but
uses
four
internal
nets
(RDBK.TRIG,
RDBK.DATA, RDBK.RIP and RDBK.CLK) that can be
routed to any IOB. To access the internal Readback sig-
nals, place the READBACK library symbol and attach the
appropriate pad symbols, as shown in Figure 27.
After Readback has been initiated by a Low-to-High transi-
tion on RDBK.TRIG, the RDBK.RIP (Read In Progress)
output goes High on the next rising edge of RDBK.CLK.
Subsequent rising edges of this clock shift out Readback
data on the RDBK.DATA net.
Readback data does not include the preamble, but starts
with five dummy bits (all High) followed by the Start bit
(Low) of the first frame. The first two data bits of the first
frame are always High.
Each frame ends with four error check bits. They are read
back as High. The last seven bits of the last frame are also
read back as High. An additional Start bit (Low) and an
11-bit Cyclic Redundancy Check (CRC) signature follow,
before RDBK.RIP returns Low.
Readback Options
Readback options are: Read Capture, Read Abort, and
Clock Select. They are set with the bitstream generation
software.
Read Capture
When the Read Capture option is selected, the readback
data stream includes sampled values of CLB and IOB sig-
nals. The rising edge of RDBK.TRIG latches the inverted
values of the CLB outputs and the IOB output and input sig-
nals.
Note that while the bits describing configuration
(interconnect and function generators) are
not inverted, the
CLB and IOB output signals
are inverted.
When the Read Capture option is not selected, the values
of the capture bits reflect the configuration data originally
written to those memory locations.
The readback signals are located in the lower-left corner of
the device.
Read Abort
When the Read Abort option is selected, a High-to-Low
transition on RDBK.TRIG terminates the readback opera-
tion and prepares the logic to accept another trigger.
After an aborted readback, additional clocks (up to one
readback clock per configuration frame) may be required to
re-initialize the control logic. The status of readback is indi-
cated by the output control net RDBK.RIP. RDBK.RIP is
High whenever a readback is in progress.
Clock Select
CCLK is the default clock. However, the user can insert
another clock on RDBK.CLK. Readback control and data
are clocked on rising edges of RDBK.CLK. If readback
must be inhibited for security reasons, the readback control
nets are simply not connected.
Violating the Maximum High and Low Time
Specification for the Readback Clock
The readback clock has a maximum High and Low time
specification. In some cases, this specification cannot be
met. For example, if a processor is controlling readback,
an interrupt may force it to stop in the middle of a readback.
This necessitates stopping the clock, and thus violating the
specification.
The specification is mandatory only on clocking data at the
end of a frame prior to the next start bit. The transfer mech-
anism will load the data to a shift register during the last six
clock cycles of the frame, prior to the start bit of the follow-
ing frame. This loading process is dynamic, and is the
source of the maximum High and Low time requirements.
Therefore, the specification only applies to the six clock
cycles prior to and including any start bit, including the
clocks before the first start bit in the readback data stream.
At other times, the frame data is already in the register and
the register is not dynamic. Thus, it can be shifted out just
like a regular shift register.
The user must precisely calculate the location of the read-
back data relative to the frame. The system must keep
track of the position within a data frame, and disable inter-
rupts before frame boundaries. Frame lengths and data for-
mats are listed in Table 11 and Table 12.
Readback with the XChecker Cable
The XChecker Universal Download/Readback Cable and
Logic Probe uses the readback feature for bitstream verifi-
cation. It can also display selected internal signals on the
PC or workstation screen, functioning as a low-cost in-cir-
cuit emulator.
READBACK
DATA
RIP
TRIG
CLK
READ_DATA
OBUF
MD1
MD0
READ_TRIGGER
IBUF
X1786
IF UNCONNECTED,
DEFAULT IS CCLK
Figure 27: Readback Schematic Example
Product Obsolete or Under Obsolescence
相關PDF資料
PDF描述
XC56309AG100AR2 IC DSP 24BIT 100MHZ 144-LQFP
XC56L307VF160 IC DSP 24BIT FIXED POINT 196-BGA
XC56L307VL160 IC DSP 24BIT FIXED POINT 196-BGA
XC5VLX220T-1FFG1136I IC FPGA VIRTEX-5 220K 1136FBGA
XC5VSX35T-X1FFG665C IC FPGA VIRTEX 5 35K 665FFGBGA
相關代理商/技術參數
參數描述
XC5202-5PQ100I 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA)
XC5202-5PQ160C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5202-5PQ208C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5202-5PQ240C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
XC5202-5TQ144C 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*