- 您現在的位置：買賣IC網 > PDF目錄300146 > XC5200SERIES (Xilinx, Inc.) Field Programmable Gate Arrays PDF資料下載
參數資料
| 型號： | XC5200SERIES |
| 廠商： | Xilinx, Inc. |
| 英文描述： | Field Programmable Gate Arrays |
| 中文描述： | 現場可編程門陣列 |
| 文件頁數： | 26/73頁 |
| 文件大?。?/td> | 598K |
| 代理商： | XC5200SERIES |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁
R
XC5200 Series Field Programmable Gate Arrays
7-114
November 5, 1998 (Version 5.2)
Configuration Timing
The seven configuration modes are discussed in detail in
this section. Timing specifications are included.
Slave Serial Mode
In Slave Serial mode, an external signal drives the CCLK
input of the FPGA. The serial configuration bitstream must
be available at the DIN input of the lead FPGA a short
setup time before each rising CCLK edge.
The lead FPGA then presents the preamble data—and all
data that overflows the lead device—on its DOUT pin.
There is an internal delay of 0.5 CCLK periods, which
means that DOUT changes on the falling CCLK edge, and
the next FPGA in the daisy chain accepts data on the sub-
sequent rising CCLK edge.
shows
a
full
master/slave
system.
An
XC5200-Series device in Slave Serial mode should be con-
nected as shown in the third device from the left.
Slave Serial mode is selected by a <111> on the mode pins
(M2, M1, M0). Slave Serial is the default mode if the mode
pins are left unconnected, as they have weak pull-up resis-
tors during configuration.
Note:
Configuration must be delayed until the INIT pins of all daisy-chained FPGAs are High.
Figure 29: Slave Serial Mode Programming Switching Characteristics
XC5200
MASTER
SERIAL
Spartan,
XC4000E/EX,
XC5200
SLAVE
XC3100A
SLAVE
XC1700E
PROGRAM
NOTE:
M2, M1, M0 can be shorted
to Ground if not used as I/O
NOTE:
M2, M1, M0 can be shorted
to VCC if not used as I/O
M2
M0 M1
DOUT
CCLK
CLK
VCC
+5 V
DATA
CE
CEO
VPP
RESET/OE
DONE
DIN
LDC
INIT
DONE
PROGRAM
D/P
INIT
RESET
CCLK
DIN
CCLK
DIN
DOUT
M2
M0 M1
M1
PWRDN
M0
M2
(Low Reset Option Used)
4.7 K
3.3 K
3.3 K
3.3 K
3.3 K
3.3 K
3.3 K
VCC
X9003_01
N/C
Figure 28: Master/Slave Serial Mode Circuit Diagram
4 TCCH
Bit n
Bit n + 1
Bit n
Bit n - 1
3 TCCO
5 TCCL
2 TCCD
1 TDCC
DIN
CCLK
DOUT
(Output)
X5379
Description
Symbol
Min
Max
Units
CCLK
DIN setup
1
TDCC
20
ns
DIN hold
2
TCCD
0ns
DIN to DOUT
3
TCCO
30
ns
High time
4
TCCH
45
ns
Low time
5
TCCL
45
ns
Frequency
FCC
10
MHz
相關PDF資料 |
PDF描述 |
|---|---|
| XC68307FG8V | 16.67 MHz, MICROCONTROLLER, PQFP100 |
| XC912DG128PV8 | 16-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP112 |
| XC95108SERIES | In-System Programmable CPLD |
| XC9572XL-10CSG48C | High Performance CPLD |
| XC9572XL-10CSG48I | High Performance CPLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC5202 | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5202-3BG225C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5202-3BG352C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5202-3HQ208C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
| XC5202-3HQ240C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays |
發布緊急采購，3分鐘左右您將得到回復。