- 您現在的位置：買賣IC網 > PDF目錄4171 > XC4003E-4VQ100I (Xilinx Inc)IC FPGA I-TEMP 5V 4SPD 100-VQFP PDF資料下載
參數資料
| 型號： | XC4003E-4VQ100I |
| 廠商： | Xilinx Inc |
| 文件頁數： | 15/68頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC FPGA I-TEMP 5V 4SPD 100-VQFP |
| 產品變化通告： | XC4000XL/E, XC9500XV, XC3100A Discontinuance 12/Apr/2010 |
| 標準包裝： | 1 |
| 系列： | XC4000E/X |
| LAB/CLB數： | 100 |
| 邏輯元件/單元數： | 238 |
| RAM 位總計： | 3200 |
| 輸入/輸出數： | 77 |
| 門數： | 3000 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | -40°C ~ 100°C |
| 封裝/外殼： | 100-TQFP |
| 供應商設備封裝： | 100-VQFP（14x14） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
R
XC4000E and XC4000X Series Field Programmable Gate Arrays
6-26
May 14, 1999 (Version 1.6)
or clear on reset and after conguration. Other than the glo-
bal GSR net, no user-controlled set/reset signal is available
to the I/O ip-ops. The choice of set or clear applies to
both the initial state of the ip-op and the response to the
Global Set/Reset pulse. See “Global Set/Reset” on
page 11 for a description of how to use GSR.
JTAG Support
Embedded logic attached to the IOBs contains test struc-
tures compatible with IEEE Standard 1149.1 for boundary
scan testing, permitting easy chip and board-level testing.
More information is provided in “Boundary Scan” on
Three-State Buffers
A pair of 3-state buffers is associated with each CLB in the
array. (See Figure 27 on page 30.) These 3-state buffers
can be used to drive signals onto the nearest horizontal
longlines above and below the CLB. They can therefore be
used to implement multiplexed or bidirectional buses on the
horizontal longlines, saving logic resources. Programmable
pull-up resistors attached to these longlines help to imple-
ment a wide wired-AND function.
The buffer enable is an active-High 3-state (i.e. an
active-Low enable), as shown in Table 13.
Another 3-state buffer with similar access is located near
each I/O block along the right and left edges of the array.
(See Figure 33 on page 34.)
The horizontal longlines driven by the 3-state buffers have
a weak keeper at each end. This circuit prevents undened
oating levels. However, it is overridden by any driver, even
a pull-up resistor.
Special longlines running along the perimeter of the array
can be used to wire-AND signals coming from nearby IOBs
or from internal longlines. These longlines form the wide
edge decoders discussed in “Wide Edge Decoders” on
Three-State Buffer Modes
The 3-state buffers can be congured in three modes:
Standard 3-state buffer
Wired-AND with input on the I pin
Wired OR-AND
Standard 3-State Buffer
All three pins are used. Place the library element BUFT.
Connect the input to the I pin and the output to the O pin.
The T pin is an active-High 3-state (i.e. an active-Low
enable). Tie the T pin to Ground to implement a standard
buffer.
Wired-AND with Input on the I Pin
The buffer can be used as a Wired-AND. Use the WAND1
library symbol, which is essentially an open-drain buffer.
WAND4, WAND8, and WAND16 are also available. See the
XACT Libraries Guide for further information.
The T pin is internally tied to the I pin. Connect the input to
the I pin and the output to the O pin. Connect the outputs of
all the WAND1s together and attach a PULLUP symbol.
Wired OR-AND
The buffer can be congured as a Wired OR-AND. A High
level on either input turns off the output. Use the
WOR2AND library symbol, which is essentially an
open-drain 2-input OR gate. The two input pins are func-
tionally equivalent. Attach the two inputs to the I0 and I1
pins and tie the output to the O pin. Tie the outputs of all the
WOR2ANDs together and attach a PULLUP symbol.
Three-State Buffer Examples
Figure 21 shows how to use the 3-state buffers to imple-
ment a wired-AND function. When all the buffer inputs are
High, the pull-up resistor(s) provide the High output.
Figure 22 shows how to use the 3-state buffers to imple-
ment a multiplexer. The selection is accomplished by the
buffer 3-state signal.
Pay particular attention to the polarity of the T pin when
using these buffers in a design. Active-High 3-state (T) is
identical to an active-Low output enable, as shown in
Table 13: Three-State Buffer Functionality
IN
T
OUT
X1
Z
IN
0
IN
P
U
L
U
P
Z = D
A
q
D
B
q
(D
C
+D
D
) q (D
E
+D
F
)
D
E
D
F
D
C
D
B
D
A
WAND1
WOR2AND
X6465
Figure 21: Open-Drain Buffers Implement a Wired-AND Function
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC4003E-4VQ100C | IC FPGA C-TEMP 5V 4SPD 100-VQFP |
| AMM36DRSI | CONN EDGECARD 72POS DIP .156 SLD |
| FMC28DRXI-S734 | CONN EDGECARD 56POS DIP .100 SLD |
| XC4003E-4PQ100I | IC FPGA I-TEMP 5V 4-SPD 100-PQFP |
| XC4003E-4PG120I | IC FPGA I-TEMP 5V 4-SPD 120-CPGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC4003H | 制造商:XILINX 制造商全稱:XILINX 功能描述:Logic Cell Array Families |
| XC4003H-4PG191C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| XC4003H-4PQ208C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| XC4003H-5PG191C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
| XC4003H-5PQ208C | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Field Programmable Gate Array (FPGA) |
發布緊急采購，3分鐘左右您將得到回復。