- 您現在的位置：買賣IC網 > PDF目錄4176 > XC3190A-3PQ160C (Xilinx Inc)IC LOGIC CL ARRAY 9000GAT 160PQF PDF資料下載
參數資料
| 型號： | XC3190A-3PQ160C |
| 廠商： | Xilinx Inc |
| 文件頁數： | 15/76頁 |
| 文件大小： | 0K |
| 描述： | IC LOGIC CL ARRAY 9000GAT 160PQF |
| 產品變化通告： | XC4000XL/E, XC9500XV, XC3100A Discontinuance 12/Apr/2010 |
| 標準包裝： | 24 |
| 系列： | XC3000A/L |
| LAB/CLB數： | 320 |
| RAM 位總計： | 64160 |
| 輸入/輸出數： | 138 |
| 門數： | 6000 |
| 電源電壓： | 4.25 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 85°C |
| 封裝/外殼： | 160-BQFP |
| 供應商設備封裝： | 160-PQFP（28x28） |
| 其它名稱： | 122-1047 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
R
XC3000 Series Field Programmable Gate Arrays
7-24
November 9, 1998 (Version 3.1)
RESET Timing
As with DONE timing, the timing of the release of the inter-
nal reset can be controlled to occur either a CCLK cycle
before, or after, the outputs going active. See Figure 22.
This reset keeps all user programmable flip-flops and
latches in a zero state during configuration.
Crystal Oscillator Division
A selection allows the user to incorporate a dedicated
divide-by-two flip-flop between the crystal oscillator and the
alternate clock line. This guarantees a symmetrical clock
signal. Although the frequency stability of a crystal oscilla-
tor is very good, the symmetry of its waveform can be
affected by bias or feedback drive.
Bitstream Error Checking
Bitstream error checking protects against erroneous con-
figuration.
Each Xilinx FPGA bitstream consists of a 40-bit preamble,
followed by a device-specific number of data frames. The
number of bits per frame is also device-specific; however,
each frame ends with three stop bits (111) followed by a
start bit for the next frame (0).
All devices in all XC3000 families start reading in a new
frame when they find the first 0 after the end of the previous
frame. An original XC3000 device does not check for the
correct stop bits, but XC3000A, XC3100A, XC3000L, and
XC3100L devices check that the last three bits of any frame
are actually 111.
Under normal circumstances, all these FPGAs behave the
same way; however, if the bitstream is corrupted, an
XC3000 device will always start a new frame as soon as it
finds the first 0 after the end of the previous frame, even if
the data is completely wrong or out-of-sync. Given suffi-
cient zeros in the data stream, the device will also go Done,
but with incorrect configuration and the possibility of inter-
nal contention.
An XC3000A/XC3100A/XC3000L/XC3100L device starts
any new frame only if the three preceding bits are all ones.
If this check fails, it pulls INIT Low and stops the internal
configuration, although the Master CCLK keeps running.
The user must then start a new configuration by applying a
>6
s Low level on RESET.
This simple check does not protect against random bit
errors, but it offers almost 100 percent protection against
erroneous configuration files, defective configuration data
sources, synchronization errors between configuration
source and FPGA, or PC-board level defects, such as bro-
ken lines or solder-bridges.
Reset Spike Protection
A separate modification slows down the RESET input
before configuration by using a two-stage shift register
driven from the internal clock. It tolerates submicrosecond
High spikes on RESET before configuration. The XC3000
master can be connected like an XC4000 master, but with
its RESET input used instead of INIT. (On XC3000, INIT is
output only).
Soft Start-up
After configuration, the outputs of all FPGAs in a
daisy-chain become active simultaneously, as a result of
the same CCLK edge. In the original XC3000/3100
devices, each output becomes active in either fast or
slew-rate limited mode, depending on the way it is config-
ured. This can lead to large ground-bounce signals. In
XC3000A, XC3000L, XC3100A, and XC3100L devices, all
outputs become active first in slew-rate limited mode,
reducing the ground bounce. After this soft start-up, each
individual output slew rate is again controlled by the
respective configuration bit.
Product Obsolete or Under Obsolescence
相關PDF資料 |
PDF描述 |
|---|---|
| XC3164A-3PC84C | IC LOGIC CL ARRAY 6400GAT 84PLCC |
| AMC36DRYN-S13 | CONN EDGECARD 72POS .100 EXTEND |
| XC3142A-3PQ100C | IC LOGIC CL ARRAY 4200GAT 100PQF |
| AMC36DRYH-S13 | CONN EDGECARD 72POS .100 EXTEND |
| XC3130A-3PQ100C | IC LOGIC CL ARRAY 3000GAT 100PQF |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XC3190A-3PQ160C0262 | 制造商:Xilinx 功能描述: |
| XC3190A-3PQ160I | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays (XC3000A/L, XC3100A/L) |
| XC3190A-3PQ208C | 制造商:Xilinx 功能描述: |
| XC3190A-3PQ208I | 制造商:Xilinx 功能描述: |
| XC3190A-3TQ144C | 制造商:XILINX 制造商全稱:XILINX 功能描述:Field Programmable Gate Arrays (XC3000A/L, XC3100A/L) |
發布緊急采購，3分鐘左右您將得到回復。