參數資料
型號： XC2S200-5FGG456C
廠商： Xilinx Inc
文件頁數： 36/99頁
文件大?。?/td> 0K
描述： IC SPARTAN-II FPGA 200K 456-FBGA
標準包裝： 60
系列： Spartan®-II
LAB/CLB數： 1176
邏輯元件/單元數： 5292
RAM 位總計： 57344
輸入/輸出數： 284
門數： 200000
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 456-BBGA
供應商設備封裝： 456-FBGA
其它名稱： 122-1312
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
41
R
IOBUF_<slew_rate>_<drive_strength>
<slew_rate> can be either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24).
When the IOBUF primitive supports an I/O standard such
as LVTTL, LVCMOS, or PCI33_5, the IBUF automatically
configures as a 5V tolerant input buffer unless the VCCO for
the bank is less than 2V. If the single-ended IBUF is placed
in a bank with an HSTL standard (VCCO < 2V), the input
buffer is not 5V tolerant.
The voltage reference signal is "banked" within the
Spartan-II device on a half-edge basis such that for all
packages there are eight independent VREF banks
internally. See Figure 36, page 39 for a representation of
the Spartan-II FPGA I/O banks. Within each bank
approximately one of every six I/O pins is automatically
configured as a VREF input.
Additional restrictions on the Versatile I/O IOBUF
placement require that within a given VCCO bank each
IOBUF must share the same output source drive voltage.
Input buffers of any type and output buffers that do not
require VCCO can be placed within the same VCCO bank.
The LOC property can specify a location for the IOBUF.
An optional delay element is associated with the input path
in each IOBUF. When the IOBUF drives an input flip-flop
within the IOB, the delay element activates by default to
ensure a zero hold-time requirement. Override this default
with the NODELAY=TRUE property.
In the case when the IOBUF does not drive an input flip-flop
within the IOB, the delay element de-activates by default to
provide higher performance. To delay the input signal,
activate the delay element with the DELAY=TRUE property.
3-state output buffers and bidirectional buffers can have
either a weak pull-up resistor, a weak pull-down resistor, or
a weak "keeper" circuit. Control this feature by adding the
appropriate primitive to the output net of the IOBUF
(PULLUP, PULLDOWN, or KEEPER).
Versatile I/O Properties
Access to some of the Versatile I/O features (for example,
location constraints, input delay, output drive strength, and
slew rate) is available through properties associated with
these features.
Input Delay Properties
An optional delay element is associated with each IBUF.
When the IBUF drives a flip-flop within the IOB, the delay
element activates by default to ensure a zero hold-time
requirement. Use the NODELAY=TRUE property to
override this default.
In the case when the IBUF does not drive a flip-flop within
the IOB, the delay element by default de-activates to
provide higher performance. To delay the input signal,
activate the delay element with the DELAY=TRUE property.
IOB Flip-Flop/Latch Property
The I/O Block (IOB) includes an optional register on the
input path, an optional register on the output path, and an
optional register on the 3-state control pin. The design
implementation software automatically takes advantage of
these registers when the following option for the Map
program is specified:
map -pr b <filename>
Alternatively, the IOB = TRUE property can be placed on a
register to force the mapper to place the register in an IOB.
Location Constraints
Specify the location of each Versatile I/O primitive with the
location constraint LOC attached to the Versatile I/O
primitive. The external port identifier indicates the value of
the location constrain. The format of the port identifier
depends on the package chosen for the specific design.
The LOC properties use the following form:
LOC=A42
LOC=P37
Output Slew Rate Property
In the case of the LVTTL output buffers (OBUF, OBUFT, and
IOBUF), slew rate control can be programmed with the
SLEW= property. By default, the slew rate for each output
buffer is reduced to minimize power bus transients when
switching non-critical signals. The SLEW= property has one
of the two following values.
SLEW=SLOW
SLEW=FAST
Output Drive Strength Property
For the LVTTL output buffers (OBUF, OBUFT, and IOBUF,
the desired drive strength can be specified with the DRIVE=
Figure 40: Input/Output Buffer Primitiveprimitive
(IOBUF)
IO
I
IOBUF
DS001_40_061200
T
O
相關PDF資料
PDF描述
745777-4 CONN D-SUB GASKET RFI 37POS TIN
24LC32AFT-E/MNY IC SRL EEPROM 4KX8 2.5V 8-TDFN
XC3S700A-4FG400I IC SPARTAN-3A FPGA 700K 400FBGA
554043-2 CONN STANDOFF M3.5 SCKT #6-32
24LC64FT-E/SN IC SRL EEPROM 8KX8 2.5V 8-SOIC
相關代理商/技術參數
參數描述
XC2S200-5FGG456C4124 制造商:Xilinx 功能描述:
XC2S200-5FGG456I 功能描述:IC SPARTAN-II FPGA 200K 456-FBGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA（27x27）
XC2S200-5PQ208C 功能描述:IC FPGA 2.5V 1176 CLB'S 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA（27x27）
XC2S200-5PQ208I 功能描述:IC FPGA 2.5V I-TEMP 208-PQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:Spartan®-II 標準包裝:40 系列:Spartan® 6 LX LAB/CLB數:3411 邏輯元件/單元數:43661 RAM 位總計:2138112 輸入/輸出數:358 門數:- 電源電壓:1.14 V ~ 1.26 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 100°C 封裝/外殼:676-BGA 供應商設備封裝:676-FBGA（27x27）
XC2S200-5PQ208Q 制造商:Xilinx 功能描述:XILINX XC2S200-5PQ208Q FPGA - Trays 制造商:Xilinx 功能描述:Xilinx XC2S200-5PQ208Q FPGA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*