參數資料
型號： XC2S100-5TQG144C
廠商： Xilinx Inc
文件頁數： 35/99頁
文件大?。?/td> 0K
描述： IC SPARTAN-II FPGA 100K 144-TQFP
標準包裝： 60
系列： Spartan®-II
LAB/CLB數： 600
邏輯元件/單元數： 2700
RAM 位總計： 40960
輸入/輸出數： 92
門數： 100000
電源電壓： 2.375 V ~ 2.625 V
安裝類型： 表面貼裝
工作溫度： 0°C ~ 85°C
封裝/外殼： 144-LQFP
供應商設備封裝： 144-TQFP（20x20）
產品目錄頁面： 599 (CN2011-ZH PDF)
其它名稱： 122-1305
Spartan-II FPGA Family: Functional Description
DS001-2 (v2.8) June 13, 2008
Module 2 of 4
Product Specification
40
R
LVTTL output buffers have selectable drive strengths.
The format for LVTTL OBUF primitive names is as follows.
OBUF_<slew_rate>_<drive_strength>
<slew_rate> is either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24). The default is slew rate limited with 12 mA drive.
OBUF placement restrictions require that within a given
VCCO bank each OBUF share the same output source drive
voltage. Input buffers of any type and output buffers that do
not require VCCO can be placed within any VCCO bank.
Table 17 summarizes the output compatibility requirements.
The LOC property can specify a location for the OBUF.
OBUFT
The generic 3-state output buffer OBUFT, shown in
Figure 39, typically implements 3-state outputs or
bidirectional I/O.
With no extension or property specified for the generic
OBUFT primitive, the assumed standard is slew rate limited
LVTTL with 12 mA drive strength.
The LVTTL OBUFT can support one of two slew rate modes
to minimize bus transients. By default, the slew rate for each
output buffer is reduced to minimize power bus transients
when switching non-critical signals.
LVTTL 3-state output buffers have selectable drive
strengths.
The format for LVTTL OBUFT primitive names is as follows.
OBUFT_<slew_rate>_<drive_strength>
<slew_rate> can be either F (Fast), or S (Slow) and
<drive_strength> is specified in milliamps (2, 4, 6, 8, 12, 16,
or 24).
The Versatile I/O OBUFT placement restrictions require
that within a given VCCO bank each OBUFT share the same
output source drive voltage. Input buffers of any type and
output buffers that do not require VCCO can be placed within
the same VCCO bank.
The LOC property can specify a location for the OBUFT.
3-state output buffers and bidirectional buffers can have
either a weak pull-up resistor, a weak pull-down resistor, or
a weak "keeper" circuit. Control this feature by adding the
appropriate primitive to the output net of the OBUFT
(PULLUP, PULLDOWN, or KEEPER).
The weak "keeper" circuit requires the input buffer within the
IOB to sample the I/O signal. So, OBUFTs programmed for
an I/O standard that requires a VREF have automatic
placement of a VREF in the bank with an OBUFT configured
with a weak "keeper" circuit. This restriction does not affect
most circuit design as applications using an OBUFT
configured with a weak "keeper" typically implement a
bidirectional I/O. In this case the IBUF (and the
corresponding VREF) are explicitly placed.
The LOC property can specify a location for the OBUFT.
IOBUF
Use the IOBUF primitive for bidirectional signals that
require both an input buffer and a 3-state output buffer with
an active high 3-state pin. The generic input/output buffer
IOBUF appears in Figure 40.
With no extension or property specified for the generic
IOBUF primitive, the assumed standard is LVTTL input
buffer and slew rate limited LVTTL with 12 mA drive strength
for the output buffer.
The LVTTL IOBUF can support one of two slew rate modes
to minimize bus transients. By default, the slew rate for each
output buffer is reduced to minimize power bus transients
when switching non-critical signals.
LVTTL bidirectional buffers have selectable output drive
strengths.
The format for LVTTL IOBUF primitive names is as follows:
Table 17: Output Standards Compatibility
Requirements
Rule 1
Only outputs with standards which share
compatible VCCO may be used within the same
bank.
Rule 2
There are no placement restrictions for outputs
with standards that do not require a VCCO.
VCCO
Compatible Standards
3.3
LVTTL, SSTL3_I, SSTL3_II, CTT, AGP, GTL,
GTL+, PCI33_3, PCI66_3
2.5
SSTL2_I, SSTL2_II, LVCMOS2, GTL, GTL+
1.5
HSTL_I, HSTL_III, HSTL_IV, GTL, GTL+
Figure 39: 3-State Output Buffer Primitive (OBUFT
IO
I
IOBUFT
DS001_39_032300
T
相關PDF資料
PDF描述
TACR476M003H CAP TANT 47UF 3V 20% 0805
XC3S400A-4FTG256C IC SPARTAN-3A FPGA 400K 256FTBGA
XC3S200AN-4FTG256C IC SPARTAN-3AN FPGA 200K 256FTBG
TACR476M002R CAP TANT 47UF 2V 20% 0805
RMC44DRYI CONN EDGECARD 88POS DIP .100 SLD
相關代理商/技術參數
參數描述
XC2S100-5TQG144I 制造商:Xilinx 功能描述:FPGA SPARTAN-II 100K GATES 2700 CELLS 263MHZ 2.5V 144TQFP EP - Trays 制造商:Xilinx 功能描述:XLXXC2S100-5TQG144I IC SYSTEM GATE
XC2S100-5VQ100C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information
XC2S100-5VQ100I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II 2.5V FPGA Family:Introduction and Ordering Information
XC2S100-5VQG100C 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
XC2S100-5VQG100I 制造商:XILINX 制造商全稱:XILINX 功能描述:Spartan-II FPGA Family
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*