- 您現在的位置：買賣IC網 > PDF目錄376449 > X95840WV20IZ-2.7 (INTERSIL CORP) Quad Digital Controlled Potentiometers PDF資料下載
參數資料
| 型號： | X95840WV20IZ-2.7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Quad Digital Controlled Potentiometers |
| 中文描述： | QUAD 10K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO20 |
| 封裝： | ROHS COMPLIANT, PLASTIC, TSSOP-20 |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 1145K |
| 代理商： | X95840WV20IZ-2.7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁
10
FN8213.1
September 27, 2005
The X95840 is pre-programed with 80h in the four IVRs.
WR: Wiper Register, IVR: Initial value Register.
2-Wire Serial Interface
The X95840 supports a bidirectional bus oriented protocol.
The protocol defines any device that sends data onto the
bus as a transmitter and the receiving device as the receiver.
The device controlling the transfer is a master and the
device being controlled is the slave. The master always
initiates data transfers and provides the clock for both
transmit and receive operations. Therefore, the X95840
operates as a slave device in all applications.
All communication over the 2-wire interface is conducted by
sending the MSB of each byte of data first.
Protocol Conventions
Data states on the SDA line can change only during SCL
LOW periods. SDA state changes during SCL HIGH are
reserved for indicating START and STOP conditions (See
Figure 15). On power up of the X95840 the SDA pin is in the
input mode.
All 2-wire interface operations must begin with a START
condition, which is a HIGH to LOW transition of SDA while
SCL is HIGH. The X95840 continuously monitors the SDA
and SCL lines for the START condition and does not
respond to any command until this condition is met (See
Figure 15). A START condition is ignored during the power
up sequence and during internal non-volatile write cycles.
All 2-wire interface operations must be terminated by a
STOP condition, which is a LOW to HIGH transition of SDA
while SCL is HIGH (See Figure 15). A STOP condition at the
end of a read operation, or at the end of a write operation to
volatile bytes only places the device in its standby mode. A
STOP condition during a write operation to a non-volatile
byte, initiates an internal non-volatile write cycle. The device
enters its standby state when the internal non-volatile write
cycle is completed.
An ACK, Acknowledge, is a software convention used to
indicate a successful data transfer. The transmitting device,
either master or slave, releases the SDA bus after
transmitting eight bits. During the ninth clock cycle, the
receiver pulls the SDA line LOW to acknowledge the
reception of the eight bits of data (See Figure 16).
The X95840 responds with an ACK after recognition of a
START condition followed by a valid Identification Byte, and
once again after successful receipt of an Address Byte. The
X95840 also responds with an ACK after receiving a Data
Byte of a write operation. The master must respond with an
ACK after receiving a Data Byte of a read operation
A valid Identification Byte contains 1010 as the four MSBs,
and the following three bits matching the logic values
present at pins A2, A1, and A0. The LSB in the Read/Write
bit. Its value is “1” for a Read operation, and “0” for a Write
operation. See Table 2.
TABLE 2. IDENTIFICATION BYTE FORMAT
TABLE 1. MEMORY MAP
ADDRESS
NON-VOLATILE
VOLATILE
8
—
Access Control
7
Reserved
6
5
4
General Purpose
Not Available
3
2
1
0
IVR3
IVR2
IVR1
IVR0
WR3
WR2
WR1
WR0
1
0
1
0
A2
A1
A0
R/W
(MSB)
(LSB)
Logic values at pins A2, A1, and A0 respectively
SDA
SCL
START
DATA
STABLE
DATA
CHANGE
STOP
DATA
STABLE
FIGURE 15. VALID DATA CHANGES, START, AND STOP CONDITIONS
X95840
相關PDF資料 |
PDF描述 |
|---|---|
| X95840UV20IZ-2.7 | Quad Digital Controlled Potentiometers |
| X96010 | Sensor Conditioner with Dual Look Up Table Memory and DACs(傳感器調節器，帶雙查找表存儲器及DACs) |
| X96010V14I | Sensor Conditioner with Dual Look Up Table Memory and DACs |
| X96010V14IZ | Hook-Up Wire; Conductor Size AWG:24; No. Strands x Strand Size:19 x 36; Jacket Color:Purple; Approval Bodies:UL; Approval Categories:UL AWM Style 1180; Passes VW-1 Flame Test; Cable/Wire MIL SPEC:MIL-W-16878/5 Type EE RoHS Compliant: Yes |
| X96011 | Temperature Sensor with Look Up Table Memory and DAC(溫度傳感器，帶雙查找表存儲器及DAC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X95RP-2 | 功能描述:消費電池與相機電池 D 18900mAh 2 PK Titanium Alkaline RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable |
| X95RP-4 | 功能描述:消費電池與相機電池 NOT AVAILABLE THROUGH MOUSER RoHS:否 制造商:FDK Batteries 電池大小:CR1/3N 輸出電壓:3 V 容量:160 mAh 化學性質:Lithium 端接類型:Pressure Contacts 可再充電/不可再充電:Non-Rechargeable |
| X96010 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Sensor Conditioner with Dual Look Up Table Memory and DACs |
| X96010V14I | 功能描述:CONDITIONER SGNL DUAL MEM & DAC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| X96010V14IZ | 功能描述:板上安裝溫度傳感器 SENSOR CONDITIONER W/DL LOOP UP TABLE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。