- 您現在的位置：買賣IC網 > PDF目錄372540 > X9521V20I (INTERSIL CORP) Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules PDF資料下載
參數資料
| 型號： | X9521V20I |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules |
| 中文描述： | DUAL 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 9/26頁 |
| 文件大?。?/td> | 434K |
| 代理商： | X9521V20I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
REV 1.1.9 1/30/03
Characteristics subject to change without notice.
9 of 26
www.xicor.com
X9521
– Preliminary Information
finally, the master issues a STOP condition. The Data
Byte read in this operation, corresponds to the “wiper
position” (value of the WCR) of the DCP pointed to by bits
P1 and P0.
It should be noted that when reading out the data byte for
DCP1 (100 Tap), the upper most significant bit is an
“unknown”. For DCP2 (256 Tap) however, all bits of the
data byte are relevant (See Figure 10).
2 kbit EEPROM ARRAY
Operations on the 2 kbit EEPROM Array, consist of either
1, 2 or 3 byte command sequences. All operations on the
EEPROM must begin with the Device Type Identifier of
the Slave Address set to 1010000. A Read or Write to the
EEPROM is selected by setting the LSB of the Slave
Address to the appropriate value R/W (Read = “1”,
Write=”0”).
In some cases when performing a Read or Write to the
EEPROM, an Address Byte may also need to be speci-
fied. This Address Byte can contain the values 00h to
FFh.
EEPROM Byte Write
In order to perform an EEPROM Byte Write operation to
the EEPROM array, the Write Enable Latch (WEL) bit of
the CONSTAT Register must first be set (See “BL1, BL0:
Block Lock protection bits - (Nonvolatile)” on page 12.)
For a write operation, the X9521 requires the Slave
Address Byte and an Address Byte. This gives the master
access to any one of the words in the array. After receipt
of the Address Byte, the X9521 responds with an
ACKNOWLEDGE, and awaits the next eight bits of data.
After receiving the 8 bits of the Data Byte, it again
responds with an ACKNOWLEDGE. The master then
terminates the transfer by generating a STOP condition,
at which time the X9521 begins the internal write cycle to
the nonvolatile memory (See Figure 11). During this
internal write cycle, the X9521 inputs are disabled, so it
does not respond to any requests from the master. The
SDA output is at high impedance. A write to a region of
EEPROM memory which has been protected with the
Block-Lock feature (See “BL1, BL0: Block Lock protection
bits - (Nonvolatile)” on page 12.), suppresses the
ACKNOWLEDGE bit after the Address Byte.
EEPROM Page Write
In order to perform an EEPROM Page Write operation to
the EEPROM array, the Write Enable Latch (WEL) bit of
the CONSTAT Register must first be set (See “BL1, BL0:
Block Lock protection bits - (Nonvolatile)” on page 12.)
The X9521 is capable of a page write operation. It is initi-
ated in the same manner as the byte write operation; but
instead of terminating the write cycle after the first data
byte is transferred, the master can transmit an unlimited
number of 8-bit bytes. After the receipt of each byte, the
X9521 responds with an ACKNOWLEDGE, and the
address is internally incremented by one. The page
address remains constant. When the counter reaches the
end of the page, it “rolls over” and goes back to ‘0’ on the
same page.
For example, if the master writes 12 bytes to the page
starting at location 11 (decimal), the first 5 bytes are writ-
ten to locations 11 through 15, while the last 7 bytes are
written to locations 0 through 6. Afterwards, the address
counter would point to location 7. If the master supplies
more than 16 bytes of data, then new data overwrites the
previous data, one byte at a time (See Figure 13).
S
t
a
r
t
S
t
o
p
Slave
Address
Address
Byte
Data
(n)
A
C
K
A
C
K
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
Data
(1)
A
C
K
(2 < n < 16)
Figure 12. EEPROM Page Write Operation
1 0 1 0 0 00 0
相關PDF資料 |
PDF描述 |
|---|---|
| X95820 | Dual Digitally Controlled Potentiometers (XDCP)(雙數控電位器) |
| X95840 | Quad Digital Controlled Potentiometers (XDCP)(四數控電位器（XDCP）) |
| x96012(中文) | Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器) |
| x96012 | Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器) |
| X9C102(中文) | EEPOT Nonvolatile Digital Potentiometer(100個抽頭,-5V~+5V,1K總電阻,非易失性數字電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9521V20I-A | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9521V20I-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9521V20IZ-A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9521V20IZ-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9522 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules |
發布緊急采購，3分鐘左右您將得到回復。