- 您現在的位置：買賣IC網 > PDF目錄372540 > X9521V20I (INTERSIL CORP) Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules PDF資料下載
參數資料
| 型號： | X9521V20I |
| 廠商： | INTERSIL CORP |
| 元件分類： | 數字電位計 |
| 英文描述： | Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules |
| 中文描述： | DUAL 100K DIGITAL POTENTIOMETER, 2-WIRE SERIAL CONTROL INTERFACE, 256 POSITIONS, PDSO20 |
| 封裝： | PLASTIC, TSSOP-20 |
| 文件頁數： | 10/26頁 |
| 文件大?。?/td> | 434K |
| 代理商： | X9521V20I |
REV 1.1.9 1/30/03
Characteristics subject to change without notice.
10 of 26
www.xicor.com
X9521
– Preliminary Information
The master terminates the Data Byte loading by issuing a
STOP condition, which causes the X9521 to begin the
nonvolatile write cycle. As with the byte write operation, all
inputs are disabled until completion of the internal write
cycle. See Figure 12 for the address, ACKNOWLEDGE,
and data transfer sequence.
Stops and EEPROM Write Modes
Stop conditions that terminate write operations must be
sent by the master after sending at least 1 full data byte
and receiving the subsequent ACKNOWLEDGE signal. If
the master issues a STOP within a Data Byte, or before
the X9521 issues a corresponding ACKNOWLEDGE, the
X9521 cancels the write operation. Therefore, the con-
tents of the EEPROM array does not change.
EEPROM Array Read Operations
Read operations are initiated in the same manner as write
operations with the exception that the R/W bit of the Slave
Address Byte is set to one. There are three basic read
operations: Current EEPROM Address Read, Random
EEPROM Read, and Sequential EEPROM Read.
Current EEPROM Address Read
Internally the device contains an address counter that
maintains the address of the last word read incremented
by one. Therefore, if the last read was to address n, the
next read operation would access data from address n+1.
On power up, the address of the address counter is unde-
fined, requiring a read or write operation for initialization.
Upon receipt of the Slave Address Byte with the R/W bit
set to one, the device issues an ACKNOWLEDGE and
then transmits the eight bits of the Data Byte. The master
terminates the read operation when it does not respond
with an ACKNOWLEDGE during the ninth clock and then
issues a STOP condition (See Figure 14 for the address,
ACKNOWLEDGE, and data transfer sequence).
It should be noted that the ninth clock cycle of the read
operation is not a “don’t care.” To terminate a read opera-
tion, the master must either issue a STOP condition dur-
ing the ninth cycle or hold SDA HIGH during the ninth
clock cycle and then issue a STOP condition.
Another important point to note regarding the “Current
EEPROM Address Read” , is that this operation is not
available if the last executed operation was an access to a
DCP or the CONSTAT Register (i.e.: an operation using
address
15
address
11
5 bytes
7 bytes
address
= 6
address pointer
ends here
Addr = 7
Figure 13. Example: Writing 12 bytes to a 16-byte page starting at location 11.
10
10
10
10
S
t
a
r
t
S
t
o
p
Slave
Address
Data
A
C
K
SDA Bus
Signals from
the Slave
Signals from
the Master
1
Figure 14. Current EEPROM Address Read Sequence
1
01
0
0 0 0
相關PDF資料 |
PDF描述 |
|---|---|
| X95820 | Dual Digitally Controlled Potentiometers (XDCP)(雙數控電位器) |
| X95840 | Quad Digital Controlled Potentiometers (XDCP)(四數控電位器（XDCP）) |
| x96012(中文) | Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器) |
| x96012 | Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器) |
| X9C102(中文) | EEPOT Nonvolatile Digital Potentiometer(100個抽頭,-5V~+5V,1K總電阻,非易失性數字電位器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X9521V20I-A | 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝 |
| X9521V20I-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9521V20IZ-A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9521V20IZ-B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory |
| X9522 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Laser Diode Control for Fiber Optic Modules |
發布緊急采購，3分鐘左右您將得到回復。