參數資料
型號： X9521
廠商： Intersil Corporation
英文描述： Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules
中文描述： 光纖通道/千兆以太網控制半導體激光器光纖模塊
文件頁數： 6/26頁
文件大小： 434K
代理商： X9521
REV 1.1.9 1/30/03
Characteristics subject to change without notice.
6 of 26
www.xicor.com
X9521
– Preliminary Information
before break” sequence is used internally for the FET
switches when the wiper is moved from one tap position
to another.
Hot Pluggability
Figure 7 shows a typical waveform that the X9521 might
experience in a Hot Pluggable situation. On power up,
Vcc applied to the X9521 may exhibit some amount of
ringing, before it settles to the required value.
The device is designed such that the wiper terminal (R
is recalled to the correct position (as per the last stored in
the DCP NVM), when the voltage applied to Vcc exceeds
V
TRIP
for a time exceeding t
pu
Therefore, if
t
trans
is defined as the time taken for Vcc to
settle above V
TRIP
(Figure 7): then the desired wiper ter-
minal position is recalled by (a maximum) time:
t
pu
. It should be noted that
t
trans
hot plug conditions.
Wx
)
.
t
trans
+
is determined by system
DCP Operations
In total there are three operations that can be performed
on any internal DCP structure:
—DCP Nonvolatile Write
—DCP Volatile Write
—DCP Read
A nonvolatile write to a DCP will change the “wiper
position” by simultaneously writing new data to the
associated WCR and NVM. Therefore, the new “wiper
position” setting is recalled into the WCR after Vcc of the
X9521 is powered down and then powered back up.
A volatile write operation to a DCP however, changes the
“wiper position” by writing new data to the associated
WCR only. The contents of the associated NVM register
remains unchanged. Therefore, when Vcc to the device is
powered down then back up, the “wiper position” reverts
to that last position written to the DCP using a nonvolatile
write operation.
Both volatile and nonvolatile write operations are
executed using a three byte command sequence: (DCP)
Slave Address Byte, Instruction Byte, followed by a Data
Byte (See Figure 9)
A DCP Read operation allows the user to “read out” the
current “wiper position” of the DCP as stored in the
associated WCR. This operation is executed using the
Random Address Read command sequence, consisting
of the (DCP) Slave Address Byte followed by an
Instruction Byte and the Slave Address Byte again (Refer
to Figure 10.).
Instruction Byte
While the Slave Address Byte is used to select the DCP
devices, an Instruction Byte is used to determine which
DCP is being addressed.
The Instruction Byte (Figure 8) is valid only when the
Device Type Identifier and the Internal Device Address
bits of the Slave Address are set to 1010111. In this
case, the two Least Significant Bit’s (I1 - I0) of the
Instruction Byte are used to select the particular DCP (0
- 2). In the case of a Write to any of the DCPs (i.e. the LSB
of the Slave Address is 0), the Most Significant Bit of the
Instruction Byte (I7), determines the Write Type (WT) per-
formed.
If WT is “1”, then a Nonvolatile Write to the DCP
this case, the “wiper position” of the DCP is changed by
simultaneously writing new data to the associated WCR
occurs. In
Figure 7.
DCP Power up
t
Vcc
V
TRIP
Vcc (Max.)
t
pu
Maximum Wiper Recall time
0
t
trans
相關PDF資料
PDF描述
X9521V20I Fiber Channel/Gigabit Ethernet Laser Diode Control for Fiber Optic Modules
X95820 Dual Digitally Controlled Potentiometers (XDCP)(雙數控電位器)
X95840 Quad Digital Controlled Potentiometers (XDCP)(四數控電位器（XDCP）)
x96012(中文) Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器)
x96012 Universal Sensor Conditioner with Dual Look Up Table Memory and DACs(帶雙查尋表存儲器和數模轉換器的通用傳感器控制器)
相關代理商/技術參數
參數描述
X9521_06 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory
X9521V20I 功能描述:IC LASR CTRLR 2CHAN 5.5V 20TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9521V20I-A 功能描述:IC DCP DUAL EEPROM MEM 20-TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 激光驅動器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:激光二極管驅動器 數據速率:- 通道數:4 電源電壓:3.3V 電流 - 電源:- 電流 - 調制:- 電流 - 偏置:- 工作溫度:0°C ~ 70°C 封裝/外殼:40-TQFN 裸露焊盤 供應商設備封裝:40-TQFN EP 包裝:托盤 安裝類型:表面貼裝
X9521V20I-B 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory
X9521V20IZ-A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual DCP, EEPROM Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*