- 您現在的位置：買賣IC網 > PDF目錄371269 > X68C75J Port Expander and E2 Memory PDF資料下載
參數資料
| 型號： | X68C75J |
| 英文描述： | Port Expander and E2 Memory |
| 中文描述： | 端口擴展和E2內存 |
| 文件頁數： | 13/26頁 |
| 文件大?。?/td> | 123K |
| 代理商： | X68C75J |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
13
X68C75 SLIC
E
2
X68C75 location E024H. The XSLIC software, a PC
based communication driver, automates changing of
the default parameters when using its SETUP option
menu. The boot-firmware (SLIC) residing on the X68C75
contains a lookup table which can be accessed from the
subroutine (EXEC_FUNC), located at location E120H.
Two bytes are used per table entry. The EXEC_FUNC
input requirements are as follows:
B = Contains a function number from the following
function table.
The table entry at location (E14E-E14FH) is reserved for
user’s application code. This function will be executed
on power-up if the SLIC receives any characters other
than those for the RESET (ASCII ‘R’), or ID (ASCII ‘X’)
commands. This table entry can be changed to point to
other code responsible for power-up initialization. This
method is preferred to changing the reset vector, since
the SLIC code can still be invoked upon power-up.
Other functions available through the EXEC_FUNC
calls are as follows:
Table 2.
the interrupt is enabled, an external interrupt will be
asserted at the completion of the internal write cycle.
The interrupt is cleared by setting EOW to “0”.
USING A PORT IN BIDIRECTIONAL MODE
In order to use a port in bidirectional mode, it has to be
configured as an open drain output port. Small pull-up
resistors are required on all port output pins. Bit positions
in the port data register corresponding to port inputs
should contain “1”. The inputs are then read by access-
ing PPR. Data is not latched into the device, so the inputs
must stay valid throughout the read cycle. The port
strobe pin is configured as an output and cannot be used
as port latch clock input.
SLIC FUNCTIONS (68HC11 Specific SLIC)
The resident SLIC E
2
has designated memory spaces
allocated for its use. The user’s application code should
avoid using these areas as part of its code segment,
otherwise it will overwrite the SLIC E
2
. Version 3.0 of the
X68C75 SLIC E
2
occupies 192 bytes in the upper
memory bank, FF00-FFC0H, and 336 bytes in the lower
bank’s address range E000-E14FH. Prior to download-
ing code, assemble and link the source files using the
above address information. Use memory space taken
up by the SLIC E
2
as a run-time data storage, if there is
no further need to modify the X68C75 SLIC E
2
content.
The current version of the SLIC E
2
configures the 68HC11
serial port to the variable baud rate mode. It sets a timer
prescalar value for a system clock rate of 8MHz. For
other clock rates, the end user must recalculate timer 1
reload value for 9600 baud rate and write it into the
Figure 13.
SLIC
E000
E150
FF00
FFC0
SLIC
User’s Program/Data
2899 ILL F15
ISR & Reset Vectors
FFFF
FUNCTION NO.
DESCRIPTION
0 - PROC_PROG
Download and program a
page
Program BPR
Start execution from
location E000H
Download and verify a page
Command not recognized
Initialize UART parameters
to default
Program a page
Send a character to the
UART
Read a character from the
RAM receive buffer (40H-5FH)
Generate SDP off sequence
for upper plane
1 - PROC_BPR
2 - RESET
3 - PROC_VER
4 - DUMMY
5 - INIT_UART
6 - PROG_PG
7 - SEND_CHAR
8 - GET_CHAR
9 - SDP_HI_PLANE
10- SDP_LO_PLANE Generate SDP off sequence
for lower plane
11- USER_CODE
Execute user’s code
2899 PGM T03.2
For detailed information about the listed functions, in-
cluding their input requirements, refer to the SLIC soft-
ware specification document.
相關PDF資料 |
PDF描述 |
|---|---|
| X68C75JI | Port Expander and E2 Memory |
| X68C75JM | Port Expander and E2 Memory |
| X68C75L | Port Expander and E2 Memory |
| X68C75LI | Port Expander and E2 Memory |
| X68C75LM | Port Expander and E2 Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| X68C75JI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X68C75JM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X68C75L | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X68C75LI | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
| X68C75LM | 制造商:XICOR 制造商全稱:Xicor Inc. 功能描述:Port Expander and E2 Memory |
發布緊急采購，3分鐘左右您將得到回復。