參數資料
型號： W78ERD2A40FL
廠商： WINBOND ELECTRONICS CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT MICROCONTROLLER
中文描述： 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP44
封裝： ROHS COMPLIANT, PLASTIC, QFP-44
文件頁數： 7/76頁
文件大?。?/td> 650K
代理商： W78ERD2A40FL
W78ERD2/W78ERD2A
Publication Release Date: February 14, 2007
- 7 -
Revision A10
Timer 2 is controlled by the T2CON register. Like Timers 0 and 1, Timer 2 can operate as either an
external event counter or an internal timer, depending on the setting of bit C/T2 in T2CON. Timer 2
has three operating modes: capture, auto-reload, and baud rate generator. In capture or auto-reload
mode, RCAP2H and RCAP2L are the reload / capture registers and the clock speed is the same as
that of Timers 0 and 1.
5.3 Clock
The W78ERD2 is designed for either a crystal oscillator or an external clock.
The W78ERD2 incorporates a built-in crystal oscillator. To make the oscillator work, a crystal must be
connected across pins XTAL1 and XTAL2, and a load capacitor may be connected from each pin to
ground. In addition, if the crystal frequency is higher than 24 MHz, a resistor should be connected
between XTAL1 and XTAL2 to provide a DC bias.
An external clock is connected to pin XTAL1, while pin XTAL2 should be left disconnected. The
XTAL1 input is a CMOS-type input, as required by the crystal oscillator. As a result, the logic-1 voltage
should be higher than 3.5 V.
5.4 Power Management
The W78ERD2 provides two modes, idle mode and power-down mode, to reduce power consumption.
Both modes are entered by software.
The W78ERD2 enters Idle mode when the IDL bit in the PCON register is set. In Idle mode, the
internal clock for the processor stops while the internal clock for the peripherals and interrupt logic
continues to run. The W78ERD2 leaves Idle mode when an interrupt or a reset occurs.
The W78ERD2 enters Power-Down mode when the PD bit in the PCON register is set. In Power-
Down mode, all of the clocks are stopped, including the oscillator. The W78ERD2 leaves Power-Down
mode when there is a hardware reset or by external interrupts
INT0
or
INT1
,
if enabled.
5.5 Reduce EMI Emission
If the crystal frequency is less than 25 MHz, set bit 7 in the option register to 0 to reduce EMI
emissions. Please see Option Bits for more information.
5.6 Reset
The external RESET signal is sampled at S5P2. To take effect, it must be held high for at least two
machine cycles while the oscillator is running, as the W78ERD2 has a special glitch-removal circuit
that ignores glitches on the reset line.
During reset, the ports are initialized to FFH, the stack pointer to 07H, and all of the other SFR to 00H,
with two exceptions—SBUF does not change, and bit 4 in PCON is not cleared.
相關PDF資料
PDF描述
W78ERD2A40PL 8-BIT MICROCONTROLLER
W78ERD2 8-BIT MICROCONTROLLER
W78ERD2A40DN 8-BIT MICROCONTROLLER
W78ERD2A40FN 8-BIT MICROCONTROLLER
W78ERD2A40PN 8-BIT MICROCONTROLLER
相關代理商/技術參數
參數描述
W78ERD2A40FN 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
W78ERD2A40PL 功能描述:IC MCU 8-BIT 64K FLASH 44-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W78 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO，I²C，LIN，UART/USART 外圍設備:DMA，LVD，POR，PWM，WDT 輸入/輸出數:27 程序存儲器容量:16KB（16K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤
W78ERD2A40PN 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
W78I052A 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
W78I052A24DL 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*