- 您現在的位置：買賣IC網 > PDF目錄363899 > W78ERD2A40FL (WINBOND ELECTRONICS CORP) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | W78ERD2A40FL |
| 廠商： | WINBOND ELECTRONICS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP44 |
| 封裝： | ROHS COMPLIANT, PLASTIC, QFP-44 |
| 文件頁數： | 42/76頁 |
| 文件大?。?/td> | 650K |
| 代理商： | W78ERD2A40FL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
W78ERD2/W78ERD2A
- 42 -
10.5 Framing Error Detection
A frame error occurs when a valid stop bit is not detected. This could indicate incorrect serial data
communication. Typically, the frame error is due to noise or contention on the serial communication
line. The W78ERD2 has the ability to detect framing errors and set a flag which can be checked by
software.
The frame error FE bit is located in SCON.7. This bit is normally used as SM0 in the standard 8051
family. However, in the W78ERD2 it serves a dual function and is called SM0/FE. There are actually
two separate flags, one for SM0 and the other for FE. The flag that is actually accessed as SCON.7 is
determined by SMOD0 (PCON.6) bit. When SMOD0 is set to 1, then the FE flag is accessed. When
SMOD0 is set to 0, then the SM0 flag is accessed.
The FE bit is set to 1 by the hardware but must be cleared by software. Once FE is set, any frames
received afterwards, even those without any errors, do not clear the FE flag. The flag has to be
cleared by software. Note that SMOD0 must be set to 1 while reading or writing to FE.
10.6 Multi-Processor Communications
Multi-processor communication makes use of the 9th data bit in modes 2 and 3. In the W78ERD2, the
RI flag is set only if the received byte corresponds to the Given or Broadcast address. This hardware
feature eliminates the software overhead required in checking every received address and greatly
simplifies the software programmer task.
In multi-processor communication mode, the address bytes are distinguished from the data bytes by
the 9th bit, which is set high for address bytes. When the master processor wants to transmit a block
of data to one of the slaves, it first sends out the address of the target slave (or slaves). All the slave
processors should have their SM2 bit set high when waiting for an address byte. This ensures that
they are interrupted only by the reception of an address byte. The automatic address recognition
feature ensures that only the addressed slave is actually interrupted because the address comparison
is done by the hardware, not the software.
The addressed slave clears the SM2 bit, thereby clearing the way to receive data bytes. With SM2 =
0, the slave is interrupted on the reception of every single complete frame of data. The unaddressed
slaves are not affected, as they are still waiting for their address.
The Master processor can selectively communicate with groups of slaves by using the Given Address.
All the slaves can be addressed together using the Broadcast Address. The addresses for each slave
are defined in the SADDR and SADEN registers. The slave address is an eight-bit value specified in
the SADDR SFR. The SADEN SFR is actually a mask for the byte value in SADDR. If a bit position in
SADEN is 0, then the corresponding bit position in SADDR is don't care. Only those bit positions in
SADDR whose corresponding bits in SADEN are 1 are used to obtain the Given Address. This gives
the user flexibility to address multiple slaves without changing the slave address in SADDR.
The following example shows how the user can define the Given Address to address different slaves.
相關PDF資料 |
PDF描述 |
|---|---|
| W78ERD2A40PL | 8-BIT MICROCONTROLLER |
| W78ERD2 | 8-BIT MICROCONTROLLER |
| W78ERD2A40DN | 8-BIT MICROCONTROLLER |
| W78ERD2A40FN | 8-BIT MICROCONTROLLER |
| W78ERD2A40PN | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| W78ERD2A40FN | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78ERD2A40PL | 功能描述:IC MCU 8-BIT 64K FLASH 44-PLCC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:W78 標準包裝:300 系列:78K0R/Ix3 核心處理器:78K/0R 芯體尺寸:16-位 速度:40MHz 連通性:3 線 SIO，I²C，LIN，UART/USART 外圍設備:DMA，LVD，POR，PWM，WDT 輸入/輸出數:27 程序存儲器容量:16KB（16K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:38-SSOP 包裝:托盤 |
| W78ERD2A40PN | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78I052A | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
| W78I052A24DL | 制造商:WINBOND 制造商全稱:Winbond 功能描述:8-BIT MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。